manualshive.com logo in svg

Poulan Pro PP1150ES, Руководство пользователя, Страница: 5 / 40

Поделиться
Скачать
Poulan Pro PP1150ES Скачать руководство пользователя страница 5

5

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER 

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is 

located on top of the belt cover.  Store the extra shear bolts, 

nuts and multi-wrench provided in parts bag in the toolbox.

NOTE:

 The multi-wrench may be used for assembly of the 

chute rotator head to snow thrower and making ad just ments 

to the skid plates.

UNFOLD UPPER HANDLE

1.  Raise upper handle to the operating position and 

tight en handle knobs securely.  Additional carriage 

bolts, washers and handle knobs are in bag of parts.  

Use to secure upper handle to lower handle.  Install 

in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.  Remove plastic tie securing rod to lower handle.
2.  Insert rod into speed control bracket and secure with 

retainer spring.

SPEED

CONTROL 

ROD

HANDLE 

KNOB

LOWER 

HANDLE

PLASTIC TIE

UPPER 

HANDLE

FIG. 1

SPEED CON TROL ROD

SPEED 

CONTROL 

BRACKET

SPEED 

CONTROL 

LEVER

FIG. 2

RETAINER 

SPRING

INSTALL TRACTION DRIVE CONTROL ROD

(See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.
1.  Remove plastic tie securing traction drive control rod 

to rotator bracket.

2.  With top end of rod positioned under left side of control 

panel, push rod down and insert top end of rod into 

hole in traction drive control lever. Snap rod into place 

by pushing down.  

NOTE:

 Engage lever once and rod should snap into place.

TRACTION DRIVE

CONTROL ROD

FIG. 3

PLASTIC TIE

FIG. 4

TRACTION DRIVE CON TROL LEVER

TRACTION DRIVE 

CON TROL ROD

Содержание PP1150ES









































Отзывы:

Нет отзывов