background image

11

OPERATION

TO THROW SNOW (See Fig. 16)

The auger rotation is controlled by the auger control lever 
located on the right side handle.

•      Squeeze auger control lever to handle to engage the 

auger and throw snow.

•      Release the auger control lever to stop throwing snow.

TO MOVE FORWARD AND BACKWARD (See Fig. 17)

SELF-PROPELLING, forward and reverse movement of 
the snow thrower, is controlled by the traction drive control 
lever located on the left side handle.

•         Squeeze traction drive control lever to handle to en gage 

the drive system.

•      Release traction drive control lever to stop the forward 

or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed 
control lever.

•      Press downward on the speed control lever and move 

lever to de sired po si tion BE FORE engaging the trac-
 tion drive control lever. Be sure lever springs back and 
locks into desired position.

AUGER 
CONTROL 
LEVER

FIG. 16

FIG. 15

DISCHARGE CHUTE

CONTROL LEVER 

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

DRIVE SPEED
CONTROL LEVER

TRACTION DRIVE 

CONTROL LEVER

FIG. 17

CAUTION: Do not move speed con trol le ver 
when traction drive control lever is en gaged. 
Damage to the snow thrower can result.

•      Slower speeds are for heavier snow and faster speeds 

are for light snow and transporting the snow thrower. It 
is recommended that you use a slower speed until you 
are familiar with the operation of the snow thrower.

NOTE:

 When both traction drive and auger control levers 

are engaged, the traction drive control lever will lock the 
auger control lever in the engaged position. This will allow 
you to release your right hand from the handle and adjust 
the discharge chute direction without interrupting the snow 
throwing process.

POWER STEERING OPERATION (See Fig. 18)

Steering triggers are used to assist in steering your snow 
thrower. The triggers are located on the underside of each 
handle. When a trigger is squeezed, it disengages the drive 
wheel on that side of snow thrower and allows it to turn in 
that direction.

•      To turn left – squeeze left side trigger.

•      To turn right – squeeze right side trigger.

LH TURN 
TRIGGER

RH TURN

TRIGGER

FIG. 18

Содержание PP1130ESA

































Отзывы: