Poulan Pro PD25PH48STE Скачать руководство пользователя страница 8

8

02510

INSTALL MOWER  AND DRIVE BELT   
(See Figs. 6 and 7)

Be sure tractor is on level surface and mower suspension 
arms are raised with attachment lift control. Engage park-
 ing brake.
•      Cut and remove ties securing anti-sway bar and belts.  

Swing anti-sway bar to left side of mower deck.

•      Slide mower under tractor with defl ector shield to right 

side of tractor.

IMPORTANT: 

 Check belt for proper routing in all mower 

pulley grooves.  
•      If  equipped,  turn  height  ad just ment knob coun 

ter -

clock wise until it stops.

ASSEMBLY

FIG. 5

TO ATTACH NOSE ROLLER (See Fig. 5)

•      Assemble brackets "A" and "B" to the inside of mower 

mounting brack ets as shown.  Tighten securely.

NOTE:

  Be sure bracket tabs are po si tioned in tab holes 

in mower brackets.
•     Position nose roller between brackets and install rod 

and retainer spring.

02612

NOSE 
ROLLER

HEX 
BOLT

"A"
BRACKET 

LOCK 
NUT

TAB
HOLE

RETAINER SPRING

ROD

"B"
BRACKET 

•      Lower mower linkage with attachment lift control.
•      Be sure belt tension rod is in dis en gaged position.
       Install belt into electric clutch pulley groove.
•      Place the suspension arms on outward pointing deck 

pins.  Retain with double loop re tain er spring with loops 
up as shown.

•     Install front plate assembly to tractor suspension 

brack ets and retain with single loop retainer springs 
as shown.

•      Position  front  plate  assembly  between  front  mower 

brackets. Raise deck and plate assembly to align holes 
and insert fl anged pins. Secure pins with double loop 
retainer springs between the plate assembly and mower 
brackets.

NOTE:

 To assist in locating hole in fl anged pin, the hole in 

pin is inline with notch on head of pin. If necessary, move 
mower side-to-side to give space between plate and mower 
brackets.

IMPORTANT: 

 Check belt for proper routing in all mower 

pulley grooves.  Engage belt tension rod by pushing rod 
into locking bracket.
•     Engage belt tension rod by pushing rod into locking 

bracket.

CAUTION: Belt tension rod is spring 
loaded. Have a tight grip on rod and 
engage slowly.

•      Connect  anti-sway  bar  to  chassis  bracket  under  left 

foot rest and retain with double loop retainer spring.

•      If equipped, turn height adjustment knob clock wise to 

remove slack from mower sus pen sion.

•      Raise deck to highest position.
•      Adjust gauge wheels before op er at ing mower as shown 

in the Operation section of this manual.

ANTI-SWAY
BAR

SINGLE LOOP 
RE TAIN ER SPRINGS

GAUGE WHEEL

SUS PEN SION ARMS

DOUBLE LOOP 
RE TAIN ER SPRING

FRONT SUS PEN SION 
BRACKETS

FRONT PLATE
AS SEM BLY

CHAS SIS
BRACKET

DOUBLE LOOP RETAINER 
SPRING (OUTWARD 
POINT ING DECK PINS)

ELECTRIC CLUTCH 
PULLEY

DE FLEC TOR SHIELD

USE PLIERS FOR

RETAINER SPRINGS

LOOP UP

FRONT 
MOWER 
BRACKET

BELT TENSION  ROD
(DISENGAGED POSITION)

LOCK BRACKET

FLANGED 
PIN

DOUBLE LOOP 
RE TAIN ER SPRING

 FIG. 6

Содержание PD25PH48STE
































Отзывы: