Poulan Pro 545186805 Скачать руководство пользователя страница 16

Страница: 16 / 20

REPLACE SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better. Ignition timing is fixed and non-

adjustable.
1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and

discard.

5. Replace with Champion RCJ--7Y spark

plug and tighten securely with a

inch

(19 mm) socket wrench. Spark plug gap

should be 0.025 inch (0,6 mm).

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3

screws. Tighten securely.

Spark

Plug

Cylinder

Cover

Spark

Plug Boot

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run-

ning it dry of fuel. Remove fuel cap and its

connected retainer from tank. Pull filter from

tank and remove from line. Replace and re-

assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

WARNING:

Improper chain sharp-

ening techniques and/or depth gauge mainte-

nance will increase the chance of kickback

which can result in serious injury.

WARNING:

Wear protective gloves

when handling chain. The chain is sharp and

can cut you even when it is not moving.

Conditions which indicate the need for chain

sharpening:

Reduction in size of wood chips. The size

of the wood chip will decrease as the chain

gets duller until it becomes more like a

powder than a chip. Note that dead or

rotted wood will not produce a good chip.

Saw cuts to one side or at an angle.

Saw has to be forced through the cut.

Tools required:

5/32 inch (4 mm) diameter round file and

file holder

Flat file

Depth gauge tool

TO SHARPEN CHAIN:

1. Move ON/STOP switch to the STOP

position.

2. Check chain for proper tension. Adjust

chain tension if necessary. See CHAIN

TENSION section.

3. Sharpen cutters.

To sharpen the cutters, position the

file holder level (90

) so that it rests

on the top edges of the cutter and

depth gauge.

NOTE:

The chain has both left and

right hand cutters.

Depth Gauge

File

File Holder

Cutter

Align the 30

file holder marks paral-

lel with the bar and to the center of the

chain.

Cutter

File Holder Line

Sharpen cutters on one side of the

chain first. File from the inside of each

cutter to the outside. Then, turn the

chain saw around and repeat the pro-

cess for the other side of the chain.

File on the forward stroke only. Use 2

or 3 strokes per cutting edge.

Keep all cutters the same length

when filing.

File enough to remove any damage

to cutting edges (side plate and top

plate of cutter).

All Cutters

Same Length

Remove Damage

Top Plate

Side Plate

File chain to meet the specifications

as shown.

Содержание 545186805





















Результаты поиска

Содержание 545186805

Отзывы:

Похожие инструкции для 545186805

Бренды по названию

Популярные бренды

Poulan Pro 545186805, Инструкция по эксплуатации

Результаты поиска

Содержание 545186805

Отзывы:

Похожие инструкции для 545186805

Бренды по названию

Популярные бренды