Poulan Pro 545047515 Скачать руководство пользователя страница 16

Страница: 16 / 19

REPLACE SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better. Ignition timing is fixed and non-

adjustable.

1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and

discard.

5. Replace with Champion RCJ--7Y spark

plug and tighten securely with a

inch

(19 mm) socket wrench. Spark plug gap

should be 0.025 inch (0,6 mm).

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3

screws. Tighten securely.

Spark

Plug

Cylinder

Cover

Spark

Plug Boot

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run-

ning it dry of fuel. Remove fuel cap and its

connected retainer from tank. Pull filter from

tank and remove from line. Replace and re-

assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY section.

CHAIN SHARPENING

Chain sharpening is a complicated task and

requires special tools. We recommend that

you refer chain sharpening to a professional

chain sharpener.

CARBURETOR ADJUSTMENT

WARNING:

The chain will be moving

during most of this procedure. Wear your pro-

tective equipment and observe all safety pre-

cautions. The chain must not move at idle

speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if

you notice any of the following conditions:

Chain moves at idle. See IDLE SPEED--T

adjusting procedure.

Saw will not idle. See IDLE SPEED--T ad-

justing procedure.

Idle Speed--T

Allow engine to idle. If the chain moves, idle is

too fast. If the engine stalls, idle is too slow. Ad-

just speed until engine runs without chain

movement (idle too fast) or stalling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is labeled T.

Turn idle screw (T) clockwise to increase

engine speed.

Turn idle screw (T) counterclockwise to

decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call our customer

assistance help line at 1--800--554--6723.

STORAGE

WARNING:

Perform the following

steps after each use:

Allow the engine to cool, and secure the

unit before storing or transporting.

Store chain saw and fuel in a well venti-

lated area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store chain saw with all guards in place

and position chain saw so that any sharp

object cannot accidentally cause injury.

Store chain saw well out of the reach of

children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the

season or if it will not be used for 30 days or

more.

If your chain saw is to be stored for a period

of time:

Clean saw thoroughly before storage.

Store in a clean dry area.

Lightly oil external metal surfaces and

guide bar.

Oil the chain and wrap it in heavy paper or

cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message

labeled

IMPORTANT

regarding the use of

gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum depos-

its during storage. Add stabilizer to the gaso-

line in the fuel tank or fuel storage container.

Follow the mix instructions found on stabiliz-

er containers. Run engine at least 5 minutes

after adding stabilizer.

Poulan/Weed Eater 40:1, 2-cycle engine oil

(air cooled) is blended with fuel stabilizer. If

you do not use this oil, you can add a fuel sta-

bilizer to your fuel tank.

Содержание 545047515




















Результаты поиска

Содержание 545047515

Отзывы:

Бренды по названию

Популярные бренды

Poulan Pro 545047515, Инструкция по эксплуатации

Результаты поиска

Содержание 545047515

Отзывы:

Бренды по названию

Популярные бренды