background image

19

engine is purchased.

LENGTH OF COVER-

AGE:

This warranty shall be for a period of two

years from the initial date of purchase.

WHAT

IS COVERED: REPAIR OR REPLACE-

MENT OF PARTS.

Repair or replacement of

any warranted part will be performed at no

charge to the owner at an approved ELEC-

TROLUX HOME PRODUCTS, INC., servic-

ing center. If you have any questions regarding

your warranty rights and responsibilities, you

should contact your nearest authorized service

center or call ELECTROLUX HOME PROD-

UCTS, INC., at 1--800--554--6723.

WARRAN-

TY PERIOD:

Any warranted part which is not

scheduled for replacement as required mainte-

nance, or which is scheduled only for regular

inspection to the effect of “repair or replace as

necessary” shall be warranted for 2 years. Any

warranted part which is scheduled for replace-

ment as required maintenance shall be war-

ranted for the period of time up to the first

scheduled replacement point for that part.

DIAGNOSIS:

The owner shall not be charged

for diagnostic labor which leads to the deter-

mination that a warranted part is defective if the

diagnostic work is performed at an approved

ELECTROLUX HOME PRODUCTS, INC.,

servicing center.

CONSEQUENTIAL DAM-

AGES:

ELECTROLUX HOME PRODUCTS,

INC., may be liable for damages to other en-

gine components caused by the failure of a

warranted part still under warranty.

WHAT IS

NOT COVERED

: All failures caused by abuse,

neglect, or improper maintenance are not cov-

ered.

ADD--ON OR MODIFIED PARTS:

The

use of add--on or modified parts can be

grounds for disallowing a warranty claim.

ELECTROLUX HOME PRODUCTS, INC., is

not liable to cover failures of warranted parts

caused by the use of add--on or modified parts.

HOW TO FILE A CLAIM:

If you have any

questions regarding your warranty rights and

responsibilities, you should contact your near-

est authorized service center or call ELEC-

TROLUX HOME PRODUCTS, INC., at

1--800--554--6723.

WHERE TO GET WAR-

RANTY SERVICE:

Warranty services or re-

pairs shall be provided at all ELECTROLUX

HOME PRODUCTS, INC., service centers.

Call: 1--800--554--6723

MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMISSION

RELATED PARTS

: Any ELECTROLUX

HOME PRODUCTS, INC., approved replace-

ment part used in the performance of any war-

ranty maintenance or repair on emission re-

lated parts will be provided without charge to

the owner if the part is under warranty.

EMIS-

SION CONTROL WARRANTY PARTS LIST:

Carburetor, Ignition System: Spark Plug (cov-

ered up to maintenance schedule), Ignition

Module, Muffler including catalyst.

MAINTE-

NANCE STATEMENT:

The owner is responsi-

ble for the performance of all required mainte-

nance as defined in the instruction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Содержание 530165293-01




















Отзывы: