14
OPERATION
TO OPERATE ON HILLS
WARNING: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.
• Choose the slowest speed before starting up or down
hills.
• Avoid stopping or changing speed on hills.
• If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
• Move motion control lever to neutral (N) position.
IMPORTANT:
THE MOTION CONTROL LEVER DOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKE PED AL IS DEPRESSED.
• To restart movement, slowly release parking brake and
clutch/brake pedal.
• Slowly move motion control lever to slowest setting.
• Make all turns slowly.
FIG. 12
02382
AT TACH MENT
LIFT LEVER
HIGH PO SI TION
LOW
POSITION
TO TRANSPORT (See Figs. 9 and 13)
When push ing or tow ing your trac tor, be sure to disengage
transmission by placing freewheel control in free wheel ing
po si tion. Free wheel control is located under the seat.
• Raise attachment lift to highest position with at tach ment
lift control.
• Raise seat and pull freewheel control up and back into
the slot and release so it is held in the disengaged
position.
3/8 WASH ER
3/8-16 LOCKNUT
GAUGE WHEEL
MOUNTING BRACKET
SHOULDER BOLT
GAUGE WHEEL
FIG. 11
TO OPERATE MOWER (See Fig. 12)
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged
will shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough,
rolling terrain or hills.
• Select desired height of cut.
• Lower mower with attachment lift control.
• Start mower blades by engaging attachment clutch
control.
• TO STOP MOWER BLADES - disengage attachment
clutch con trol.
CAUTION: Do not operate the mower
without either the en tire grass catcher,
on mowers so equipped, or the defl ector
shield in place.
• Adjust mower to desired cutting height (See “TO AD-
JUST MOWER CUT TING HEIGHT” in the Operation
sec tion of this manual).
• With mower in desired height of cut po si tion, gauge
wheels should be assembled so they are slightly off
the ground. In stall gauge wheel in appropriate hole
with shoulder bolt, 3/8 washer, and 3/8-16 locknut and
tighten se cure ly.
• Repeat for opposite side installing gauge wheel in same
adjustment hole.
ATTACHMENT
CLUTCH LEVER
"ENGAGED"
POSITION
"DIS EN GAGED"
POSITION
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse direc-
tion with the attachment clutch engaged will shut off the engine
unless ignition key is placed in the ROS "ON" position.
WARNING:
Backing up with the attachment clutch en-
gaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged.
Do not mow in reverse unless
absolutely necessary
.
USING THE REVERSE OPERATION SYSTEM -
Only use if you are certain no children or other bystanders
will enter the mowing area.
• Move motion control lever to neutral (N) position.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before and while backing.
• Slowly move motion control lever to reverse (R) po si tion
to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
ROS "ON" POSITION
ENGINE "ON" POSITION
(NORMAL OPERATING)
02828
