Poulan Pro 406281 страница 7 Скачать руководство пользователя

Страница: 7 / 32

ASSEMBLY / PRE-OPERATION

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR
HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotator head.

1. Place discharge chute assembly on top of chute base

with discharge opening toward front of snow thrower.

2. Position chute rotator head over chute bracket. If nec es -

sary, rotate chute assembly to align square and pin on un-
der side of chute rotator head with holes in chute brack et.

3. With chute rotator head and chute bracket aligned,

po si tion chute rotator head on pin and threaded stud
of mounting bracket.

4. Install 3/8 washer and locknut on threaded stud and

tighten securely.

CHECK TIRE PRESSURE

The tires on your snow thrower were overinfl ated at the fac-
tory for shipping purposes. Correct and equal tire pres sure
is important for best snow throwing performance.
• Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
1. Install remote cable bracket to discharge chute with

5/16-18 carriage bolt and 5/16-18 locknut as shown.
Tighten securely.

2. Install remote cable eyelet to chute defl ector with

1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut
as shown. Tighten securely.

3. Install spring hooks between hex nuts on chute rotater

head and into hole in chute defl ector as shown.

CHUTE DEFLECTOR
CONTROL LEVER

FIG. 9

CHUTE
ROTATOR
HEAD

3/8 WASHER

3/8 LOCKNUT

THREADED

STUD

PIN

ROTATOR HEAD

MOUNT ING

BRACKET

CHUTE
BRACKET

FIG. 7

ALIGN BEFORE

TIGHTENING LOCKNUT

HOOK
BE TWEEN
HEX NUTS
ON CHUTE
ROTATER
HEAD

SPRING

CHUTE

DE FLEC TOR

5/16-18

CARRIAGE

BOLT

5/16-18
LOCKNUT

REMOTE

CABLE

BRACKET

1/4-20
LOCK NUT

CABLE
EYELET

NYLON
WASHER

1/4-20
SHOULDER
BOLT

FIG. 8

Содержание 406281

































Результаты поиска

Содержание 406281

Отзывы:

Похожие инструкции для 406281

Бренды по названию

Популярные бренды

Poulan Pro 406281, Руководство пользователя

Результаты поиска

Содержание 406281

Отзывы:

Похожие инструкции для 406281

Бренды по названию

Популярные бренды