background image

23

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP1130ES

  (96192001300)

CONTROL PANEL / DISCHARGE CHUTE

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    183334            Knob, Lever
   2    17501010        Screw  #10-24 x 5/8
   3    198475            Control Assembly, Defl ector
   4    73800600        Nut, Lock  3/8-16
   5    19131316        Washer, Flat  3/8
   6    198473            Control Assembly, Chute Rotater
   7    405784X479    Support, Pivot
   8    150078            Screw, Hex Head  5/16-18 x 3/4
   9    184505            Spring, Defl ector

10    179829            Bolt, Shoulder

 11    179246            Washer, Friction, Nylon

12    191730            Nut, Lock  1/4-20
13    72250505        Bolt, Carriage  5/16-18
14    751153            Nut, Lock  5/16-18
15    404770X428    Chute Assembly
16    178633X428    Defl ector Assembly
17    179145            Seal, Defl ector
18    128415            Rivet, Blind
19    183333            Knob, Speed Control Lever
20    72270506        Bolt, Carriage  5/16-18 x 3/4
22    74041024        Screw  #10-24 x 1-1/2
23    188303            Control Assembly, Power Steering
25    198541            Nut, Lock  5/16-18
26    198474            Lever Assembly, Speed Control
27    169675            Retainer, Hairpin
28    180445            Rod, Upper, Speed Control
29    187716            Rod, Lower, Speed Control
30    192710            Clamp, Mounting, Clean-Out Tool
31    192199            Tool, Clean-Out

NOTE:  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your unit and void your warranty.

Содержание 406275

































Отзывы: