background image

4

Idaho, Maine, Minnesota, New Jersey, Ore-

gon, and Washington require by law that

many internal combustion engines be

equipped with a spark arresting screen. If you

operate in a locale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts. Failure

to do so is a violation of the law. For normal

homeowner use, the muffler and spark arrest-

ing screen will not require any service. After

50 hours of use, we recommend that your

muffler be serviced or replaced by your autho-

rized service dealer.

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following

list:

S

Brushcutter

S

Blade shield screws (4)

S

Cupped washer

S

Large nut for installing blades

S

Hex wrench

S

Metal shield

S

Plastic shield

S

Shoulder strap with warning

S

4--point weed blade

S

Trimmer head (assembled on unit)

S

Handlebar (assembled on unit)

S

Wing nut (screwed onto shield)

S

Container of oil

WARNING:

Always stop unit and dis-

connect spark plug before performing any as-

sembly procedures.

WARNING:

If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE:

If you need assistance or find parts

missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer.

TOOLS REQUIRED

S

Hex wrench (provided)

S

Adjustable wrench

ADJUST AND SECURE THE HAN-

DLEBAR

DANGER:

To avoid serious injury, the

barrier portion of the handlebar must be ad-

justed and remain installed as shown to pro-

vide a barrier between operator and the spin-

ning blade. The handlebar clamp must be

positioned between the arrows on the handle-

bar decal.

1. Lift handlebar to upright position.

Handlebar

2. Rotate handlebar/clamp counterclock-

wise toward engine until clamp falls into

groove of base.

Handlebar

Handlebar

Clamp

Clamp

Knob

Clamp

Base

3. Place the handlebar in a comfortable

position.

4. Retighten handlebar by turning clamp

knob clockwise until handlebar is secure

and stationary in clamp base (clamp

knob can not be overtightened).

ASSEMBLY OF SHOULDER STRAP

WARNING:

Proper shoulder strap

and handlebar adjustments are required before

starting the engine.

1. Try on shoulder strap and adjust for fit and

balance before starting the engine or begin-

ning a cutting operation.

2. Insert your right arm and head through

the shoulder strap and allow it to rest on

your left shoulder. Make sure the danger

sign is on your back and the hook is to the

right side of your waist.

NOTE:

A one-half twist is built in the shoulder

strap to allow the strap to rest flat on the shoul-

der.

3. Adjust the strap, allowing the hook to be

about 6 inches below the waist.

4. Fasten the strap hook to the clamp located

between the trigger handle and the handle-

bar clamp base and lift the tool to the oper-

ating position.

Содержание 331
















Отзывы: