background image

21

SERVICE AND ADJUSTMENTS

FIG. 24

TRANSAXLE  MOTION CONTROL LE 

VER 

NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been pre set at the factory and 
adjustment should not be necessary.
•      Loosen adjustment bolt in front of the right rear wheel, 

and lightly tighten.

•      Start engine and move motion control lever until tractor 

does not move forward or backward.

•        

Hold motion control lever in that position and turn engine 
off.

•      While holding motion control lever in place, loosen the 

adjustment bolt.

•      Move motion control lever to the neutral (N) (lock gate) 

position.

•      Tighten adjustment bolt securely.

NOTE:  

If additional clearance is needed to get to ad just ment 

bolt, move mower deck height to the lowest position.
After above adjustment is made, if the tractor still creeps 
forward or backward while motion control lever is in neutral 
position, follow these steps:
•      Loosen the adjustment bolt.
•     Move the motion control lever 1/4  to 1/2 inch in the 

direction it is trying to creep.

•      Tighten adjustment bolt securely.
•      Start engine and test.
•      If  tractor  still  creeps,  repeat  above  steps  until  satis-

fi ed.

TO REPLACE MOTION DRIVE BELT 
(See Fig. 25)

Park the tractor on level surface.  En gage parking brake.  
For as sis tance, there is a belt installation guide decal on 
bottom side of left footrest.

BELT REMOVAL -
 •     Remove mower (See “TO RE MOVE MOWER” in this 

section of  manual).

NOTE:

 Observe entire motion drive belt and position of all 

belt guides and keepers.
 •     Remove belt from stationary idler and clutching idler.
 •     Remove belt downward from around en gine pulley.

ENGINE 
PULLEY

CLUTCH ING 
IDLER

STA TION ARY 
IDLER

TRANS MIS SION 
INPUT PULLEY

CENTER SPAN
KEEPER

FIG. 25

WITH PARKING BRAKE “ENGAGED”

JAM NUT

DO NOT TOUCH THIS NUT.  IF FURTHER 
BRAKE AD JUST MENT IS NECESSARY CON-
TACT YOUR NEAREST AUTHORIZED SERVICE 
CENTER/DEPARTMENT

OPERATING 
ARM

NUT “A”

1-9/16”

TO CHECK BRAKE
•      Park tractor on a level, dry concrete or paved surface, 

depress clutch/brake pedal all the way down and en-
gage parking brake.

•     Disengage transmission by placing freewhel control 

in “transmission disengaged” position. Pull freewheel 
con trol out and into the slot and release so it is held in 
the disengaged position.

The rear wheels must lock and skid when you try to manually 
push the tractor forward. If the rear wheels rotate, the brake 
needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE
•      Depress clutch/brake pedal all the way down and en-

 gage parking brake.

•      Measure distance between brake operating arm and 

nut “A” on brake rod.

•     If distance is other than 1-9/16", loosen jam nut and 

turn nut “A” until distance becomes 1-9/16".  Retighten 
jam nut against nut “A”.

•      Engage transmission by placing freewheel control in 

“trans mis sion engaged” position.

•      Road test tractor for proper stopping distance as stated 

above.  Readjust if nec es sary.  If stopping distance is 
still greater than fi ve (5) feet in high est gear, further 
main te nance is nec es sary.  Replace brake pads or 
contact a qualifi ed service center.

 •     Pull belt slack toward rear of trac tor.  Carefully remove 

belt upwards from transmission input pulley and over 
cooling fan blades.

 •    Remove belt from center span keeper and pull belt 

away from tractor.

BELT INSTALLATION -
 •    Carefully work new belt down around transmission 

cooling fan and onto the input pulley.

 •     Slide belt into the center span keeper.
 •     Pull belt toward front of tractor and roll around the top 

groove of engine pulley.

 •    Install belt through stationary idler and clutch 

ing 

idler.

 •    Make sure belt is in all pulley grooves and in side all 

belt guides and keep ers.

 •     Install mower (See “TO IN STALL MOWER” in this sec-

 tion of manual).

Содержание 188774













































Отзывы: