background image

16

01202

MAINTENANCE

FIG. 13

FIG. 12

BATTERY

Your tractor has a battery charging system which is suf fi  cient 
for normal use.  However, periodic charging of the battery 
with an automotive charger will extend its life.
•      Keep battery and terminals clean.
•      Keep battery bolts tight.
•      Keep small vent holes open.
•      Recharge at  6-10 amperes for 1 hour.

NOTE:

 The original equipment battery on your tractor is 

maintenance free. Do not attempt to open or remove caps 
or covers. Adding or checking level of electrolyte is not 
nec es sary.

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause 
the battery to “leak” power.
•      Disconnect BLACK battery cable fi rst  then RED  bat-

 tery cable and remove battery from tractor.

TRACTOR

Always observe safety rules when performing any main-
 te nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance 
at high speed in highest gear, then brake must be adjusted. 
(See “TO ADJUST BRAKE” in the Service and Ad just ments 
section of this manual).

TIRES

•         Maintain proper air pressure in all tires (See “PROD UCT 

SPECIFICATIONS” section of this man ual).

•      Keep tires free of gasoline, oil, or insect control chemi-

 cals which can harm rubber.

•     Avoid stumps, stones, deep ruts, sharp objects and 

other hazards that may cause tire damage.

NOTE: 

To seal tire punctures and prevent fl at tires due to 

slow leaks, tire sealant may be purchased from your local 
parts dealer. Tire sealant also prevents tire dry rot and 
corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock sys tems are work-
 ing properly.  If your tractor does not function as described, 
repair the problem immediately.
•     The engine should not start unless the clutch/brake 

pedal is fully depressed and attachement clutch control 
is in the disengaged position.

•         When the engine is running, any attempt by the op er a tor 

to leave the seat without fi rst setting the parking brake 
should shut off the engine.

•      When the engine is running and the at tach ment clutch 

is engaged, any attempt by the operator to leave the 
seat should shut off the engine.

•     The attachment clutch should never operate unless 

the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp.  Re place 
bent or damaged blades.

5/8" BOLT 
OR PIN

BLADE

CENTER HOLE

TO SHARPEN BLADE (See Fig. 13)

NOTE:

  We do not recommend sharpening blade - but if 

you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced.  An un-
 bal anced blade will cause excessive vibration and even tual 
dam age to mower and engine.
•      The blade can be sharpened with a fi le or on a grind-

ing wheel.  Do not attempt to sharpen while on the 
mower.

•      To check blade balance, you will need a 5/8" diameter 

steel bolt, pin, or a cone balancer.  (When using a 
cone balancer, follow the instructions supplied with 
bal anc er.)

NOTE: 

 Do not use a nail for balancing blade.  The lobes of 

the center hole may appear to be centered, but are not.
•         Slide blade on to an unthreaded portion of the steel bolt 

or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal 
position.  If either end of the blade moves downward, 
sharpen the heavy end until the blade is balanced.

01

214

MANDREL
ASSEMBLY

BLADE

TRAILING
EDGE UP

LOCK WASHER

BLADE BOLT 

BLADE REMOVAL (See Fig. 12)

•     Raise mower to highest position to allow access to 

blades.

•      Remove blade bolt, lock washer and fl at washer se cur ing 

blade.

•      Install new or resharpened blade with trailing edge up 

towards deck as shown.

IMPORTANT:

 TO ENSURE PROPER ASSEMBLY, CENTER 

HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL 
ASSEMBLY.

•     Reassemble blade bolt, lock washer and fl at washer 

in exact order as shown.

•      Tight en blade bolt se cure ly (27-35 Ft. Lbs. torque).

IMPORTANT

:   BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS 

REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN 
IN THE REPAIR PARTS.

FLAT WASHER

CENTER 
HOLE

STAR

Содержание 188737

















































Отзывы: