background image

16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, 
before performing any service or ad-
 just ments:

1. Be sure throttle is in STOP position.

2. Remove safety ignition key.

3. Make sure the augers and all mov ing 

parts have completely stopped.

4. Disconnect spark plug wire from 

spark plug and place wire where it 
can not come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” 
in the Operation section of this manual.

CHUTE DEFLECTOR

The chute defl ector, attached to the top of the discharge 
chute, is provided to direct discharging snow away from 
the operator. If the defl ector becomes damaged, it should 
be re placed.

WARNING: To avoid serious injury, 
nev er operate your snow thrower with 
the defl ector removed or damaged.

•         To change direction and/or distance snow is dis charged, 

see “TO CONTROL SNOW DISCHARGE” in the Op-
 er a tion section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger 
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear 
bolts are designed to break, preventing damage to any 
other com po nents. If one or both augers do not turn when 
auger control lever is engaged, check to see if one or both 
of the bolts have sheared. To replace the shear bolts:

1.    Disengage  all  controls  and  move  throttle  control  to 

STOP position. Wait for all moving parts to stop.

2.    Disconnect spark plug wire from spark plug and place 

it wear it cannot come in contact with spark plug.

3.   Align hole in auger hub with hole in auger shaft and 

install a new 1/4-20 x 2" shoulder/shear bolt. Install
1/4-20 lock nut and tighten securely.

CAUTION: Do not sub sti tute. Use only original 
equip ment shear bolts as sup plied with your 
snow thrower.

4.    Connect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) 
capscrew/shear bolts and hex nuts. Should a foreign object 
or ice become lodged in the impeller, the capscrews are 
de signed to break, preventing damage to any other com-
 po nents. If impeller does not turn when auger control lever 
is engaged, check to see if the capscrews have sheared. 
To replace the capscrew/shear bolts:

1.    Disengage  all  controls  and  move  throttle  control  to 

STOP position. Wait for all moving parts to stop.

2.    Disconnect spark plug wire from spark plug and place 

it wear it cannot come in contact with spark plug.

3.    Align holes in impeller hub with holes in impeller shaft 

and install two (2) new 1/4-20 x 1-5/8" capscrew/shear 
bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original 
equip ment capscrew/shear bolts as sup plied 
with your snow thrower.

4.    Connect spark plug wire to spark plug.

TO REMOVE BELT COVER (See Fig. 19)

1.   Remove the two (2) screws securing belt cover to 

frame.

2.    Remove belt cover.

•      Replace belt cover by installing cover and screws and 

tighten securely.

BELT 

COVER

SCREWS

FRAME

FIG. 19

FIG. 18

AUGER SHAFT

1/4-20 x 2

SHOULDER /

SHEAR BOLT

1/4-20 
LOCK NUT

IMPELLER 

SHAFT

1/4-20 x 1-5/8
CAPSCREW / 
SHEAR BOLT

1/4-20
LOCKNUT

IMPELLER HUB

AUGER 

HUB

AUGER HUB

Содержание 187881





















Отзывы: