Poulan Pro 184518 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

background image

19

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 21)

The mower blade drive belt may be replaced without tools.
Park the tractor on level surface. Engage parking brake.
BELT REMOVAL -
•      Remove  mower  from  tractor  (See  “TO  REMOVE

MOW ER” in this section of this manual).

•      Work belt off both mandrel pulleys and idler pulleys.
•      Pull belt away from mower.
BELT INSTALLATION -
•      Install new belt in reverse order of removal.
•     Make sure belt is in all pulley grooves and in side all

belt guides.

• Install mower in reverse order of removal instruc-

tions.

SERVICE AND ADJUSTMENTS

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT:

DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE

FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY,
BE SURE TO AD JUST BOTH FRONT LINKS EQUAL LY SO

MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing
should be adjusted so that the front is approximately 1/8"
to 1/2" lower than the rear when the mower is in its high-
est position.

Check adjustment on right side of tractor. Measure dis tance
“D” directly in front and behind the mandrel at bottom edge
of mower housing as shown.
• Before making any necessary adjustments, check that

both front links are equal in length.

• If links are not equal in length, adjust one link to same

length as other link.

• To lower front of mower loosen nut “E” on both front

links an equal number of turns.

FIG. 20

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

FIG. 19

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground
or driveway. Make sure tires are properly infl ated (See
“PROD UCT SPECIFICATIONS” section of this manual). If
tires are over or underinfl ated, you will not properly adjust
your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)
• Raise mower to its highest position.
• At the midpoint of both sides of mower, measure height

from bot tom edge of mower to ground. Distance “A”
on both sides of mower should be the same or within
1/4" of each other.

• If adjustment is necessary, make adjustment on one

side of mower only.

• To raise one side of mower, tighten lift link ad just ment

nut on that side.

• To lower one side of mower, loosen lift link ad just ment

nut on that side.

NOTE

: Each full turn of adjustment nut will change mow er

height about 1/8".
• Recheck measurements after adjusting.

BOTTOM EDGE
OF MOWER TO
GROUND

FIG. 17

FIG. 18

A

A

GROUND LINE

BOTTOM EDGE

OF MOWER TO

GROUND

• When distance “D” is 1/8" to 1/2" lower at front than

rear, tighten nuts “F” against trunnion on both front
links.

• To raise front of mower, loosen nut “F” from trunnion on

both front links. Tighten nut “E” on both front links an
equal number of turns. The two front links must remain
equal in length.

• When distance “D” is 1/8" to 1/2" lower at front than rear,

tighten nut “F” against trunnion on both front links.

• Recheck side-to-side adjustment.

SUS PEN SION ARM

LIFT LINK
ADJUSTMENT NUT

“D”

“D”

MAN DREL

NUT “E”

TRUNNION

NUT “F”

FRONT LINKS

«
...
17
18
19
20
21
...
»

Содержание 184518

















































Отзывы:

Нет отзывов

Похожие инструкции для 184518

Бренд: Sears Страницы: 37

MULTICLIP Pro 51 S

Бренд: Stiga Страницы: 10

MULTICLIP MULTICLIP 46 S SVAN

Бренд: Stiga Страницы: 2

Бренд: Grasshopper Страницы: 56

Бренд: Snapper Страницы: 44

Бренд: Mowox Страницы: 219

Бренд: Einhell Royal Страницы: 24

Бренд: Poulan Pro Страницы: 29

Parklander 2690997

Бренд: Murray Страницы: 36

Бренд: VonHaus Страницы: 20

Бренд: ECLOZ Страницы: 56

Бренд: Cub Cadet Страницы: 36

Бренд: Flymo Страницы: 12

Бренд: Cub Cadet Страницы: 44

Бренд: Husqvarna Страницы: 52

Бренд: Husqvarna Страницы: 48

Бренд: Husqvarna Страницы: 48

Бренд: Husqvarna Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды