Poulan Pro 115327926 Скачать руководство пользователя

Страница: 8 / 20

8. If chain is too loose, it will sag below the

guide bar. DO NOT operate the saw if

the chain is loose.

NOTE:

The chain is tensioned correctly

when the weight of the chain does not cause it

to sag below the guide bar (with the chain saw

sitting in an upright position), but the chain still

moves freely around the guide bar.

WARNING:

If the saw is operated

with a loose chain, the chain could jump off the

guide bar and result in serious injury to the op-

erator and/or damage the chain making it un-

usable. If the chain jumps off the guide bar, in-

spect each drive link for damage. Damaged

chain must be repaired or replaced.

OPERATION

KNOW YOUR CHAIN SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of

the various controls and adjustments. Save this manual for future reference.

Chain

Adjustment Tool

(Bar Tool)

Primer Bulb

Starter Housing

Bar Oil Fill Cap

Chain

Front Hand Guard

Front Handle

Starter Rope

ON/STOP

Switch

Muffler

Choke/

Fast Idle

Lever

Fuel Mix Fill Cap

Bar

Sprocket

Hole

Guide Bar

Bar Nuts

Cylinder Cover

Throttle

Lockout

Rear

Handle

Throttle

Trigger

Chain

Brake

Chain

Direction

of Travel

Adjusting Screw

Chain

Catcher

Clutch Cover

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine

speed.

THROTTLE LOCK--OUT

The THROTTLE LOCK--OUT must be

pressed before you can squeeze the throttle

trigger. This feature prevents you from acci-

dentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulling the

CHOKE/FAST IDLE LEVER out to the full ex-

tent for cold starting or after refueling. The

choke provides additional fuel to the engine

during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the car-

buretor to provide quicker starting.

CHAIN BRAKE

The chain brake is a device designed to stop

the chain if kickback occurs. The chain brake

activates automatically in the event of kick-

back. The chain brake activates manually if the

front hand guard is pushed forward. The chain

brake is disengaged by pulling the front hand

guard back toward the front handle as far as

possible.

CHAIN TENSION

It is normal for a new chain to stretch during the

first 15 minutes of operation. You should check

your chain tension each time before you start

the chain saw. See CHAIN TENSION under

the ASSEMBLY section.

Содержание 115327926





















Результаты поиска

Содержание 115327926

Отзывы:

Похожие инструкции для 115327926

Бренды по названию

Популярные бренды

Poulan Pro 115327926, Инструкция по эксплуатации

Результаты поиска

Содержание 115327926

Отзывы:

Похожие инструкции для 115327926

Бренды по названию

Популярные бренды