Poulan Pro 115270726 Скачать руководство пользователя страница 18

Страница: 18 / 22

7. Carefully remove new chain from pack-

age. Hold chain with the drive links as

shown.

CUTTERS MUST FACE IN

DIRECTION OF ROTATION

Tip of

Bar

Cutter

Drivelink

Cutters

Depth Gauge

Drive Links

8. Place chain over sprocket, fitting the

drive links in the sprocket.

9. Fit bottom of drive links between the teeth

in the sprocket in the nose of the guide

bar.

10. Fit chain drive links into bar groove.

11. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive links

are in the bar groove.

12. Now, install bar clamp making sure the

adjusting pin is positioned in the lower

hole in the guide bar.

Adjusting Pin

Lower

Hole

Guide Bar

13. Install bar clamp nut and finger tighten

only. Do not tighten any further at this

point. Proceed to the CHAIN ADJUST-

MENT section.

CHAIN ADJUSTMENT

See CHECK CHAIN TENSION in MAINTE-

NANCE section.

CARBURETOR IDLE SPEED

ADJUSTMENT

WARNING:

Keep others away when

making idle speed adjustments. The chain

will be moving during most of this procedure.

Wear your protective equipment and observe

all safety precautions. After making adjust-

ments, the chain must not move at idle speed.

The carburetor has been carefully set at the

factory. Adjustment to the idle speed may be

necessary if you notice any of the following

conditions:

Engine will not idle when the throttle is re-

leased.

The chain moves at idle.

Make adjustments with the unit supported so

the pruner is off the ground and the chain will

not make contact with any object. Hold the

unit by hand while running and making adjust-

ments. Keep all parts of your body away from

the chain and muffler.

To adjust idle speed:

Allow engine to idle. Adjust idle speed until en-

gine runs without chain moving (idle too fast)

or stalling (idle speed too slow).

Turn idle speed screw clockwise to in-

crease engine speed if engine stalls or dies.

Turn idle speed screw counterclockwise to

decrease engine speed if chain moves at idle.

WARNING:

Recheck the idle speed

after each adjustment. The chain must not

move at idle speed to avoid serious injury to

the operator or others.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure

about performing this procedure, contact your

authorized

service

dealer

call

1--800--554--6723.

Содержание 115270726























Результаты поиска

Содержание 115270726

Отзывы:

Бренды по названию

Популярные бренды

Poulan Pro 115270726, Инструкция по эксплуатации

Результаты поиска

Содержание 115270726

Отзывы:

Бренды по названию

Популярные бренды