Poulan Pro 115156526 Скачать руководство пользователя страница 17

Страница: 17 / 21

File chain to meet the specifications

as shown.

Rounded

Corner

0.025 inch

(0.65 mm)

Right

Hook Angle

Wrong

Squared Off

Corner

Too Much Hook Angle

WARNING:

Maintain the proper hook

angle according to the manufacturer’s specifi-

cations for the chain you are using. Improper

hook angle will increase the chance of kick-

back which can result in serious injury.

4. Check and lower depth gauges.

Depth Gauge Tool

Depth Gauge

File

Place gauge tool on cutter.

If the depth gauge is higher than the

depth gauge tool, file it level to the top of

the depth gauge tool.

Maintain rounded front corner of

depth gauge with a flat file.

NOTE:

The very top of the depth

gauge should be flat with the front

half rounded off with a flat file.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call our customer

assistance help line at 1--800--554--6723.

CARBURETOR ADJUSTMENT

WARNING:

The chain will be moving

during most of this procedure. Wear your

protective equipment and observe all safety

precautions. The chain must not move at idle

speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if

you notice any of the following conditions:

Chain moves at idle. See IDLE SPEED--T

adjusting procedure.

Saw will not idle. See IDLE SPEED--T ad-

justing procedure.

Idle Speed--T

Allow engine to idle. If the chain moves, idle is

too fast. If the engine stalls, idle is too slow. Ad-

just speed until engine runs without chain

movement (idle too fast) or stalling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is labeled T.

Turn idle screw (T) clockwise to increase

engine speed.

Turn idle screw (T) counterclockwise to

decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call our customer

assistance help line at 1--800--554--6723.

COOLING SYSTEM

To keep the working temperature as low as

possible the machine is equipped with a

cooling system.

The cooling system consists of:

Air intake on the starter

Air guide plate

Fins on the flywheel

Cooling fins on the cylinder

Cylinder cover (directs cold air over the

cylinder)

Clean the cooling system with a brush after

each use, more often in demanding condi-

tions. A dirty or blocked cooling system re-

sults in the machine overheating which

causes damage to the piston and cylinder.

Содержание 115156526






















Результаты поиска

Содержание 115156526

Отзывы:

Poulan Pro 115156526, Инструкция по эксплуатации, Страница: 17 / 21

Результаты поиска

Содержание 115156526

Отзывы: