Pottinger Profi Gp 1 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 54

background image

Hydraulic opening and closing of the tail gate

Nobody should be within the swinging
range of the tail gate when opening
and closing!

Do not stand underneath the raised tail
gate!

- Opening and closing is effected

hydraulically from the tractor seat.

In doing so, the locking hooks (58) are
unlocked and locked automatically.

Unloading with lowered top frame

- Lock tubular frame against raising (hook left and right into position

B).

- The tail gate swings backwards when

opening.

Unloading with raised top frame

- Unlock tubular frame to raise (hook left and

right into position A).

- The tail gate and the tubular frame swing all

the way to the top when opening.

Adjustments

• So that the opening and closing of the tail gate

functions properly, set the adjusting screws
left and right according to the following
sequence.

- Turn the hexagonal screw (57) until the lower

pipe of the tail gate fits into the slotted plate (K).

- Set a gap (1-3 mm) by means of the hexagonal

screw (56).

- Slip the yoke end of the frame (G) from the pin

and turn it until the hooks (58) rest, without
play, on the pipe.

- Check that all lock nuts are firmly fixed.

TD 27/93/20

A

B

TD79/90/38

TD79/90/39

- 35 -

537 / RÜCKWAND 9500 GB

GB

TAIL GATE

«
...
33
34
35
36
37
...
»

Содержание Profi Gp 1























































Отзывы:

Нет отзывов

Похожие инструкции для Profi Gp 1

Бренд: ABB Страницы: 78

Бренд: ABB Страницы: 70

Бренд: R&S Страницы: 60

Бренд: ADDER Страницы: 2

Бренд: Comtech EF Data Страницы: 102

Бренд: ICP DAS USA Страницы: 3

Бренд: Samlexpower Страницы: 56

Бренд: Mitsubishi Страницы: 143

Бренд: National Instruments Страницы: 53

Бренд: B&B Electronics Страницы: 7

Бренд: FBS Страницы: 6

Бренд: KONANlabs Страницы: 6

CompactGROUND GS10plus

Бренд: AEROCOMPACT Страницы: 27

Бренд: Weco Страницы: 56

Бренд: SHENZHEN ENCOM ELECTRIC TECHNOLOGIES CO. Страницы: 30

Бренд: Eleris Страницы: 184

Бренд: Apantac Страницы: 2

Бренд: HEIDENHAIN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды