manualshive.com logo in svg

Potterton WH 46, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Potterton WH 46 Скачать руководство пользователя страница 9

9

926.772.1 - GB/IE

INSTRUCTIONS PERTAINING TO THE USER

All the faults are displayed in order of importance; if several faults occur simultaneously, the first to be displa-
yed is the one with highest priority.  After the cause of the first fault has been removed, the second one will 
be displayed, and so on.
If any given fault occurs frequently, contact the authorised Service Centre.

3.9 FAULT WARNINGS TABLE

Fault code

Fault description

action required

E10

outdoor temperature probe sensor failure

call the authorised service centre.

E20

ntc output sensor failure

call the authorised service centre

E40

NTC return heating probe faulty

call the authorised service centre

E50

domestic hot water ntc sensor failure

call the authorised service centre

E110

Safety or fumes thermostat or heating return 
temperature probe tripped

press the reset key (for about 2 seconds: if this device is triggered 
repeatedly, call the authorised service centre)

E111

Delivery temperature higher than 95°C

If this fault persists, call the authorised service centre

E128

Loss of flame during operation (the ionization current 
has fallen below the limit)

Call an authorised service centre.

E129

Minimum fan speed limit is hurt

Call an authorised service centre.

E132

floor thermostat tripped

call the authorised service centre

E133

no gas

press the reset key (for about 2 seconds); if the fault persists, 
call the authorised service centre)

E151

boiler circuit board error

Press the reset button if the display presents the (   ) symbol, 
otherwise switch off the boiler at the mains and switch it on again 
after 10 seconds. If the fault persists, call an authorised service 
centre. Check the position of the ignition electrodes (chapter 17).

E153

the reset key has been pressed inappropriately

press the key again (about 2 seconds)

E154

No circulation or reverse flow

call the authorised service centre

E160

fan speed threshold not reached

call the authorised service centre.

E164

no hydraulic pressure switch enabling signal

check that the system is at the rated pressure. (refer to the 
section on filling the system). if the fault persists, call the 
authorised service centre.

Содержание WH 46





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды