manualshive.com logo in svg

Potterton Thames, Инструкции по установке и обслуживанию

Поделиться
Скачать
Potterton Thames Скачать руководство пользователя страница 3

2. TECHNICAL SPECIFICATIONS - Page 3

Finish

White stoved paint with contrasting chassis

Weight Packed

20.9 kg. (46.0 lb.)

Weight without Water

17.7 kg. (39.0 lb.)

Weight with Water

18.5 kg. (40.7 lb.)

Water Capacity

0.75 litre (0.17 gall.)

Input

30.3 kW (103,000 Btu/h.)

Maximum Output

23.3 kW (79,500 Btu/h.)

Flow Rates

6.5 1/min at 50ºC rise

Minimum pressure head requirement at water heater *

1 bar (14.6 psi) under flow conditions

Maximum pressure head

13 bar (189 psi)

Gas group

G20

Burner injector (14 off)

1.2mm marking 120

Pilot injector

0.27mm marking A

Nominal burner pressure ** (maximum input)

12.5 mbar (5 in. w.g.)

Connections - Gas

15mm Copper Tail

- Water

15mm Compression

Balanced flues (telescopic) Wall thickness available

100mm - 150mm (4in - 6in) - Part No 31 /10321
150mm - 230mm (6in - 9in) - Part No 31/10322
230mm - 380mm (9in - 15in) - Part No 31/10323
380mm - 610mm (15in - 24in) - Part No 31/1 0324

Flue Terminal Guard (Optional)

Part No 10/10262

Notes: * Additional external pipework and fittings may affect the resistance and must be taken into account on installation.

**

The nominal burner pressure should be 12.5 mbar and will only be obtained if the appliance inlet pressure is 20 mbar
even when the appliance is running at full heat input. The meter should be capable of passing 1 OOft3/h I gas plus the
requirements of any other gas appliances.

MINIMUM CLEARANCES

Above:

60mm

Below:

75mm

Sides:

5mm (Each)

Front:

220mm (To allow for removal of outer case)

For ease of servicing, allow as much clearance as possible below the appliance.
If the appliance is to be installed in a cupboard, the ventilation openings in the cupboard must NOT be blocked.
DO NOT USE THE CUPBOARD FOR STORAGE.

Fig. 1

Supplied by HeatingSpares247.com

Содержание Thames
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды