Potterton Paramount four Скачать руководство пользователя страница 99

Страница: 99 / 144

Charging prio storage tank (3822)

If several heat exchangers/indirect coils are tied into the system, the heat

ing sequence for the connected cylinders can be determined by setting the

heating process.

None: Every storage tank is charged alternately with a temperature in

crease of 5 °C, until the setpoint has reached level A, B or C (tab. 1).

Once all setpoints have been reached, the setpoints of the next level are

applied.

Hot water storage tank: The DHW storage tank is charged as priority

during any heating with solar energy at any level (A, B or C). Other con

sumers with the same level will only be charged afterwards. Once all

setpoints have been reached, the setpoints of the next level are applied.

For this, heating the DHW cylinder still takes priority.

Buffer storage tank: During any heating with solar energy, the buffer

storage tank is charged first at any level (A, B or C). Other consumers

with the same level will only be charged afterwards. Once all setpoints

have been reached, the setpoints of the next level are applied. For this,

charging the buffer cylinder still takes priority.

Tab.22 Storage tank setpoints

Lev

Domestic water stor

age tank

Buffer storage tank

Swimming pool

(1)

Nominal value

(prog. no. 1610)

Buffer setpoint

(drag-pointer)

Setpoint solar heat

ing

(prog. no. 2055)

Charging temp max

(prog. no. 5050)

Charging temp max

(prog. no. 4750)

Setpoint solar heat

ing

(prog. no. 2055)

Storage tank temp

max

(prog. no. 5051)

Storage tank temp

max

(prog. no. 4751)

Swimming pool temp

max

(prog. no. 2070)

(1) With swimming pool heating set as priority (prog. no. 2065), the swimming

pool will be heated before the storage tanks.

For more information, see

Charging priority solar (2065), page 93

Charging time relative prio (3825)

If the preferred storage tank corresponding to the charging control not be

charged, during the time set here the priority goes to the next storage tank

or the swimming pool.

Waiting time relative prio (3826)

Transfer of priority is delayed by the time selected here.

Waiting time parallel op (3827)

Parallel operation is feasible when using solar primary pumps subject to

there being sufficient solar energy available. For this, in addition to the

storage tank currently being heated, the next storage tank in the priority

order can also be heated in parallel. The storage tank switching on for par

allel operation can be delayed and stepped by the value set here.

Delay secondary pump (3828)

Operation of the secondary pump of the heat exchanger/indirect coil can

be delayed to enable any cold water that may be present to be flushed

through the primary circuit first by the pump.

Collector start function (3830)

If the temperature at the collector with the pump turned off is not meas

ured correctly (e.g. with vacuum tubes), then a periodic switching on of the

pump is possible.

9 Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

Содержание Paramount four

















































































































































Результаты поиска

Содержание Paramount four

Отзывы:

Potterton Paramount four, Руководство по установке, Страница: 99 / 144

Результаты поиска

Содержание Paramount four

Отзывы: