manualshive.com logo in svg

Potterton Illusion, Инструкция по установке и обслуживанию

Поделиться
Скачать
Potterton Illusion Скачать руководство пользователя страница 1

Part No. 966/9350/1 – 02

Potterton Housewarmer Illusion ASD - G.C. NO. 37 590 16

966 Inset DGF with ILLUSION FACIA

Potterton Housewarmer Stratton ASD - G.C. NO. 37 590 17

966 Inset DGF with STRATTON FACIA

Potterton Housewarmer Presence ASD - G.C. NO. 37 590 18

966 Inset DGF with PRESENCE FACIA

Installation & Service Instructions

Inset Decorative Gas Fire for use with the

Potterton Housewarmer 45 & 55 BBu's

THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS 1994.

‘‘In your own interest, and that of safety, it is law that all gas appliances are installed by competent persons,

in accordance with the above regulations. Failure to install appliances correctly could lead to prosecution.’’

The polythene bags used for packaging are a potential hazard to babies and young children

and MUST BE DISPOSED OF IMMEDIATELY.

LEAVE THESE INSTRUCTIONS WITH THE USER FOR USE ON FUTURE CALLS

For Use With Natural Gas

(G20) Only At 20mbar

For Use in GB & IE

IMPORTANT

PLEASE READ THIS BOOK
BEFORE INSTALLING,
OPERATING OR
SERVICING THIS
APPLIANCE.

Содержание Illusion



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды