POSIFLEX Aura PP-7000IIUSB Скачать руководство пользователя страница 37

Страница: 37 / 40

5 - 5

SOFTWARE COMMANDS

The Aura thermal printer supports all commands applicable

to Epson printer TM-T88II. The only difference is the
smoothening command in enlarged text fonts. Please visit our
web site

http://www.posiflex.com

http://www.posiflex.com.tw

for detail description of the supported commands if required.

Paper out alarm

When Paper End signal is detected, the printer keeps on

intensive beeping and stops receiving data till the signal is
neutralized.

When Paper Near End signal is detected, the

printer gives a beep every 3 seconds and stops receiving data.

Enhancement commands

Following commands are included in the printer firmware

version since ver. 3.2:

ESC ‘o’: Beep command
GS ‘o’ m: Beep definition (0 < m

≦

16, default 3 seconds)

ESC ‘p’ m n1 n2: Cash drawer kick or kitchen bell drive

command

GS ‘p’ m n: Beep when cash drawer remain open (0 < m <

256, n = ‘0’ or ‘1’)

Explanations as below:

ESC ‘o’: Beep command

Hexadecimal codes are: 1B 6F
Printer beeps when this command is received per condition

set by beep definition.

GS ‘o’ m: Beep definition (0 < m

≦

16, default 3 seconds)

Hexadecimal codes are: 1D 6F m

Содержание Aura PP-7000IIUSB









































Результаты поиска

Содержание Aura PP-7000IIUSB

Отзывы:

Похожие инструкции для Aura PP-7000IIUSB

Бренды по названию

Популярные бренды

POSIFLEX Aura PP-7000IIUSB, Руководство пользователя

Результаты поиска

Содержание Aura PP-7000IIUSB

Отзывы:

Похожие инструкции для Aura PP-7000IIUSB

Бренды по названию

Популярные бренды