4
8.
Install Front Plate with the six 4-40 flat head
screws.
9.
Apply diameter indexed N
2
O/O
2
gas label in
place over diameter indexed check valve
connector bushings. Pull off center strip backing,
and press label in place. Remove top and
bottom backing strips, and finish securing label.
10.
Connect an 8060 series duplex connector and
hoses into the completely assembled Triple
Outlet Station. Attach the other end of the hoses
to a flowmeter and turn the flow control knobs to
the off position and the on/off switch to the off
position.
11.
Leak test
the entire system for working
pressure leaks
.
Pressurize the sedation gas
supply lines with 50 PSI. Observe any pressure
decay overnight. This 50 PSI test with the
flowmeter tubing connections in place tests the
seal of the duplex connector extended into the o-
rings of the outlet station primary check valves.
(5 PSI drop allowed.)
12.
Attach the appropriate vacuum lines from the
rubber goods to the outlet station vacuum source
via the quick connect (5602).
CONNECTIONS TO FLOWMETER –
OPERATING INSTRUCTIONS
Flowmeter Gas Supply Tubing and Vacuum Tubing is
connected to the Triple Outlet Station via two quick
connect couplers. The Porter 8060 series duplex
connector simultaneously connects the Oxygen and
Nitrous oxide tubing, and prevents the Nitrous Oxide
from being connected unless the Oxygen is
connected. The Porter 5602 vacuum quick connect
with hose barb separately inserts into the vacuum
check valve of the station.
QUICK CONNECTING
You may quick connect to the station when the
system pressure is at its normal 50 PSI; the primary
check valves seal this pressure. Both couplers have
locating latches. Simply insert the couplers into the
appropriate check valve and confirm the latch is in
place behind the catch feature of the valve. A gentle
tug on the coupler will confirm a stable latch position.
Internally, within the primary check valve, an o-ring
seals against a poppet. The same o-ring seals
against the quick connect extensions upon insertion.
Slide the latch out of position to remove the
connector and the internal poppet will automatically
move back into its sealing position.
OXYGEN RESUSCITATOR
By removing the duplex connector, an oxygen
resuscitator quick connect may be inserted into the
oxygen station position.
MAINTENANCE AND SERVICE
Use Scavenging
Monitor for N2O in the operatory to insure that
controls are effective in achieving low levels of ppm
(parts per million) exposure. Contact your Porter
dealer for details on monitors and testing.
Inspect and maintain
the analgesia delivery
system to prevent N2O leaks in all hoses,
connections and fittings. Repair all leaks
immediately.
Opposite position for 5602 right angle
vacuum quick connect hose barb:
Reconfigure
the fitting using the following steps if you need the
barb to point in the opposite direction.
Clip Reversal Instructions:
1.
Note orientation of Clip on Assembly: Hold
assembly with Hose Barb in the down position,
and with the smooth post facing you.
1.1. Note the position of the clip on the
assembly. This is important, as you will
need to rotate the clip 180
°
from its
original position.
2.
Remove the Crescent Ring using the blade of a
small flat blade screwdriver.
3.
Lift the clip from the assembly, and as you do so,
the spring will fall from the clip.
4.
Slide the clip back onto the assembly in a
position 180
°
from its original location.
5.
As the clip is brought down onto the post, place
the spring onto the pin (located on the clip), and
tuck the opposite end into the pocket on the
adapter body.
6.
Again using a flat bladed screwdriver, push the
Crescent Ring back into the groove on the post.
Orient the Crescent Ring such that the opening in
the ring faces away from the spring.
7.
Actuate clip to ensure proper operation of the
assembly.
