20
1. To remove, loosen and remove the four
screws (1) on the table inserts (2) with a
Phillips screwdriver and remove the table
inserts.
2. To install, reposition the table inserts,
install the four screws and tighten.
FIG. Q
BEVEL STOP ADJUSTMENT
7RDYRLGLQMXU\IURPDQDFFLGHQWDOVWDUW
PDNHVXUHWKHVZLWFKLVLQWKH2))SRVLWLRQ
DQGWKHSOXJLVQRWFRQQHFWHGWRWKHSRZHU
source outlet.
° (0°)
%HYHO$GMXVWPHQW)LJ56
1. Loosen bevel lock handle (1) and tilt
the cutting arm completely to the right.
Tighten the bevel lock handle (1).
NOTE:
Make sure the detent block (2)
touches the bevel angle adjustment
bolt (3). (Fig. R)
3ODFHDFRPELQDWLRQVTXDUHRQWKH
miter table (5) with the ruler against the
WDEOHDQGKHHORIWKHVTXDUHDJDLQVWWKH
saw blade. (Fig. S)
3. If the blade is not 90°
VTXDUHZLWKWKH
miter table, loosen the bevel lock
handle (1), tilt the cutting head to the left,
loosen the lock nut (6) and turn the bevel
angle adjustment bolt (3) in or out with
an adjustable wrench until the blade is
VTXDUHZLWKWKHWDEOH2QFHDOLJQPHQW
is achieved, tighten the lock nut (6) to
secure the bolt (3). (Fig. R)
4. Tighten the bevel lock handle (1) after
alignment is achieved.
)LJ5
4. Press the arbor lock button (5), holding
LWLQ¿UPO\ZKLOHWXUQLQJWKHEODGHZUHQFK
counterclockwise. Continue to press it in
while tightening the arbor bolt securely.
(Fig. O)
5. Rotate the cover plate (3) back to its
original position and tighten the cover
plate screw (2) with a Phillips screwdriver.
(Fig. N)
6. Lower the blade guard (1) back to its
original position.
7. Pull the switch handle down and up
VHYHUDOWLPHVWRFRQ¿UPWKHORZHUEODGH
guard operates without binding.
8. Be sure the arbor lock button (5) is
released so the blade turns freely. (Fig. O)
ŏ
7RDYRLGLQMXU\QHYHUXVHWKHVDZ
ZLWKRXWWKHFRYHUSODWHVHFXUHLQ
SODFH,WNHHSVWKHDUERUEROWIURP
IDOOLQJRXWLILWDFFLGHQWDOO\ORRVHQV
DQGKHOSVSUHYHQWWKHVSLQQLQJEODGH
IURPFRPLQJRIIWKHVDZ
ŏ
,IWKHFRYHUSODWHLVQRWVHFXUHLQLWV
SURSHUSODFHWKHJXDUGPD\FRQWDFW
WKHVSLQQLQJVDZEODGHUHVXOWLQJ
LQGDPDJHWRWKHVDZDQGVHYHUH
SHUVRQDOLQMXU\
ŏ
0DNHVXUHWKHFROODUVDUHFOHDQDQG
SURSHUO\DUUDQJHG/RZHUWKHEODGH
LQWRWKHWDEOHDQGFKHFNIRUDQ\
FRQWDFWZLWKWKHPHWDOEDVHRUWKH
VDZWDEOH
ŏ
ALWAYS MAKE DRY RUNS
(UNPOWERED) BEFORE FINISH CUTS
SO THAT YOU CAN CHECK THE PATH
OF THE BLADE AND THE OPERATION
OF THE GUARDS. DO NOT CROSS
HANDS.
REMOVING AND INSTALLING THE TABLE
INSERT (FIG. Q)
7RDYRLGLQMXU\
Ɣ $OZD\VXQSOXJWKHVDZWRDYRLG
DFFLGHQWDOVWDUWLQJ5HPRYHDOOVPDOO
SLHFHVRIPDWHULDOIURPWKHWDEOH
FDYLW\EHIRUHSHUIRUPLQJDQ\FXWV
7KHWDEOHLQVHUWPD\EHUHPRYHGIRU
WKLVSXUSRVHEXWDOZD\VUHDWWDFK
WKHWDEOHLQVHUWSULRUWRSHUIRUPLQJD
FXWWLQJRSHUDWLRQ
Ɣ 'RQRWVWDUWWKHPLWHUVDZZLWKRXW
FKHFNLQJIRULQWHUIHUHQFHEHWZHHQWKH
EODGHDQGWDEOHLQVHUW'DPDJHFRXOG
result to the blade, table insert or
WXUQWDEOHLIEODGHVWULNHRFFXUVGXULQJ
WKHFXWWLQJRSHUDWLRQ
WARNING
!
WARNING
!
1
2
WARNING
!
View from rear of machine
1
3
6
2
7
8
