Porter-Cable PCC670, Инструкция по эксплуатации

Страница: 10 / 40

10
• In thin gauge sheet metals it is best to clamp wood to the underside of the sheet. This will
ensure a clean cut without excess vibration or tearing of metal.
• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.
NOTE: You should spread a thin film of oil or other coolant along the line ahead of the
saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is
preferred.
POCkET CUTTING - WOOD ONLY- FIGURE k
• Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber.
• Insert blade in blade clamp and tighten blade clamp securely.
• Tip the saw backward until the back edge of the shoe is firmly on the work surface.
• Switch motor on, permitting blade to attain maximum speed.
• Grip handle steadily and begin a slow, deliberate upward swing with the handle of the saw.
• The blade will begin to feed into material. Always be sure blade is completely through
material before continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide.
PROJECT TIPS
• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.
• When cutting, always ensure that the shoe is resting against the workpiece. This will
improve operator control and minimize vibration.
• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to
high speed steel teeth making the blade more flexible and less prone to breaking.
MAINTENANCE
WARNING:
REMOVE BATTERy FROM SAW WHEN PERFORMING ANy
CLEANING OR OTHER MAINTENANCE. WHEN SERVICING USE ONLy IDENTICAL
REPLACEMENT PARTS.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various
types of commercial solvents and may be damaged by their use. Use only mild soap and
damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
• When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are
subject to accelerated wear and possible premature failure, as the fiberglass chips and
grindings and drywall dust are highly abrasive to bearings, brushes, commutator, etc.
During any use on fiberglass or drywall it is extremely important that the tool be cleaned
frequently by blowing with an air jet.
LUBRICATION
your tool was properly lubricated before leaving the factory. Once every year take or
send your tool to a PORTER-CABLE service center, or authorized service station, for
a complete cleaning, inspection and lubrication. Tools “out of service” for long periods
should be relubricated before being put back to work.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
Li-Ion battery (or battery pack) indicates that the costs to recycle the battery
(or battery pack) at the end of its useful life have already been paid by
PORTER-CABLE.
RBRC™ in cooperation with PORTER-CABLE and other battery users,
has established programs in the United States to facilitate the collection of
spent Li-Ion batteries. Help protect our environment and conserve natural resources by
returning the spent Li-Ion battery to an authorized PORTER-CABLE service center or
to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery.
RBRC™ is a registered trademark of the
Rechargeable Battery Recycling Corporation.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Replacement Parts
Use only identical replacement parts. For a parts list or to order parts, visit our service website
at www.portercable.com. you can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at (888) 848-5175.