background image

12- ENG

D25805

STARTING

Prior to starting, refer to your engine manual for proper starting procedures
for your engine type.
1.

In a well ventilated outdoor area 

Add fresh high quality unleaded gasoline

with a pump octane rating of 86 or higher.  Do not overfill. Wipe up spilled
fuel before starting the engine. Refer to engine manual for correct procedure.

2.

Check engine oil level.

See Engine Operators Manual for correct procedure. 

NOTE: There will be a slight amount of oil in the engine from factory testing.
3.

Verify the filter screen

is in water inlet of pump. 

NOTE:

Cone side faces out.

4.

Connect

water source to pump inlet.

NOTE:

Water source must provide a minimum of 5

gallons per minute at 20 p.s.i. 

5.

Connect

high pressure hose to pump outlet.

6.

If applying a chemical or cleaning solution

, see How

To Siphon Chemicals/Cleaning Solvents in Operation
section of this manual.

7.

Turn water source on. NOTE:

Make sure water

supply is turned on.

8.

Start engine.

See Engine operators Manual for

correct procedure. 

NOTE: 

If the engine does not

start after two pulls, pull the trigger to relieve the
pressure. 

9.

Depress trigger on gun to start water flow. NOTE:
Stand on a stable surface

and grip gun/wand firmly

with both hands. Expect the gun to kick when
triggered.

10. Release trigger to stop water flow.
11. Adjust nozzle spray for the task

being performed or change quick connect

tip. See 

How To Use Wand

instructions in this section.

TO SHUT DOWN

IMPORTANT: Read and understand how to shut down the pressure washer
before operating.

1.

If you have siphoned chemicals, siphon a bucket of clean water through the
chemical hose.  

NOTE: 

Failure to do so will cause damage to the pump.

2.

Refer to engine manual for correct engine shut down procedure.

NOTE:  NEVER turn the water off with the engine running.

3.

Turn water source off.  

4.

Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.

See Storage section in this manual for proper storage procedures.

Filter Screen

High Pressure Hose

Water
Source

Содержание D25805-025-1





















Отзывы: