background image

9

SERVICE AND REPAIRS

All quality tools eventually require servicing or replacement of parts due to
wear from normal use. Some user serviceable components are described in
the TROUBLESHOOTING Section. Complete product Service is available
from either an AUTHORIZED PORTER-CABLE SERVICE STATION or a
PORTER-CABLE SERVICE CENTER. All repairs made by these agencies are
fully guaranteed against defective material and workmanship. We cannot
guarantee repairs made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).

TROUBLESHOOTING

CAUTION: 

Disconnect tool from air supply before performing any

Service Procedure.

SYMPTOM PROBLEMS

SOLUTIONS

1. Air leak near top of

Loose screws.

Tighten screws. 

tool or in trigger area.

Worn or damaged

Install “OVERHAUL” Maintenance Kit. 

o-rings or seals.

2. Tool does nothing or

Inadequate air supply.

Verify adequate air supply.

operates sluggishly.

Inadequate lubrication.

Put 5 or 6 drops of oil into air inlet.

Worn or damaged   

Install “DRIVER” Maintenance Kit. 

o-rings or seals.

3. Air leak near bottom

Loose screws.

Tighten screws.

of tool.

Worn or damaged

Install “OVERHAUL” Maintenance Kit.

o-rings or bumper.

4. Tool jams frequently.

Incorrect fasteners.

Verify approved fasteners of 
correct size.                             

Damaged fasteners.

Replace w/undamaged fasteners.

Magazine or nose

Tighten screws.

screws loose.
Magazine is dirty.

Clean magazine.                             

Driver is worn or damaged.

Install “DRIVER” Maintenance Kit.

5. Other.

Contact a Porter-Cable 
Service Facility.

Содержание 894884-003













Отзывы: