poolstar 57001A Скачать руководство пользователя страница 3

Страница: 3 / 20

Safety notice

Please follow the safety instructions concerning the installation and use of this

electrical equipment:

This equipment must not be manipulated by children less than 8 years old and

persons with reduced sensory or mental abilities, or lacking experience and

knowledge, if they are not properly supervised and if instructions related to the

safe use of the equipment have not been provided and if risks incurred were

not ascertained. Children must not play with the equipment. Cleaning and

maintenance of the equipment is not to be done by children without supervi

sion.

The pump must not be installed in swimming pools. It must be installed and

used according to installation regulations NFC 15-100.

Please ensure the filtration pump is situated at least 2 meters away from the

side of the swimming pool.

The pump electric plug must be situated at least 3.5 meters from the swimmi

ng pool.

Please consult with your specialized electrician.

Warning:

risk of electrical shock. This product is protected with an earth

safety. If you are unable to check whether your installation is equipped with

earth safety or a circuit breaker, please contact an experienced technician

prior to installation. Maximum leakage value must not exceed 30mA.

Warning:

please disconnect the power supply to the equipment before mo

ving, cleaning or adjusting the product.

Warning:

do not bury the cable underground and install it in a secure place

where lawn mower and other equipment cannot damage it.

The power cable must not be replaced. If it has been damaged, do not use the

equipment.

Warning:

to reduce any risk of electric shock, do not connect to an extension

cable, a timer or a converter. Only use the electric plug provided.

Warning:

do not connect or disconnect the electric plug if you are in a wet

environment or if your hands are wet.

Warning:

after installation, the electric plug must be positionned in a way to

be visible and accessible by users.

Содержание 57001A





















Результаты поиска

Содержание 57001A

Отзывы:

Похожие инструкции для 57001A

Бренды по названию

Популярные бренды

poolstar 57001A, Руководство пользователя

Результаты поиска

Содержание 57001A

Отзывы:

Похожие инструкции для 57001A

Бренды по названию

Популярные бренды