manualshive.com logo in svg

PoolRite PoolTherm P series, Руководство по установке

Поделиться
Скачать
PoolRite PoolTherm P series Скачать руководство пользователя страница 17

5

5.  MAINTeNANCe ANd INSPeCTION

5.3 Guide for Poor Heat Gain
POOL WATER IS NOT HEATING UP:

• Is the heat pump turned on ?
• What is the temperature set too ?
• Is there sufficient water flow ?
• How long is the heat pump set to run for ?
• Are there any water features ?
• Does the pool have a blanket ?
• What is the ambient temperature ?
• Is the condenser covered in ice ?
• Are bypass valves closed off ?

NOTE: IF THE CONDENSER IS COVERED IN ICE 

Set the parameter 02 to 30 minutes 

Set parameter 03 to 0 

Set parameter 05 to 15 minutes

5.4 Customer Responsibilities

BEFORE YOU CALL FOR SERVICE

 read the following points carefully which are your responsibility.

• A service charge will be made for service as a result of:

• Power not turned on or disrupted
• Heat pump not set to run for a long enough period
• Heat pump installed incorrectly
• Recirculation pump not operating correctly
• Controls incorrectly set
• Poor water chemistry (Salt Level, pH, etc)
• Poor water flow (Check filter is clean/Pump operation/Skimmer free of obstructions and bypass flow is not excessive)
• Heat pump being tampered with by unauthorized persons
• Excessive ambient conditions

Содержание PoolTherm P series























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды