background image

3

4

4

Should you encounter any problems, contact the Customer Service at (888) 919-0070.

Should you encounter any problems, contact the Customer Service at (888) 919-0070.

KEY     DESCRIPTION

1              O-RING (RETURN FITTING ELBOW)
2              RETURN FITTING ELBOW
3              O-RING (RETURN FITTING ELBOW INTERNAL)
4              TOP COVER RETAINER
5              TOP COVER
6              HOSE RETAINING NUT
7              UV TUBE, 10W
8              UV TUBE SOCKET
9              WATERPROOF GLASS TUBE
10            BOTTOM COVER
11            WATER HOSE (IN)
12            WATER HOSE (OUT)
13            CORD CLAMP
14            PHILLIPS HEAD SCREWS
15            BALLAST
16            STRAIN RELIEF
17            EXTENSION CORD
18            POWER ADAPTER
19            MAIN HOUSING
20            O-RING (MAIN HOUSING)
21            PARTITION BOARD
22            O-RING (VENT SCREW)
23            VENT SCREW
24            HOSE ADAPTER (1.5” TO 1.25”)
25            HOSE CLAMP SCREW
26            HOSE CLAMP
27            POWER SWITCH
28            POOL WALL

FIG.1

POOL

RETURN

FITTING

POOL

WALL

FIG.2

POOL

RETURN

FITTING

POOL

SUCTION

FITTING

24

25

26

2 Ea.

4 Ea.

4 Ea.

3

1.

READ ALL INSTRUCTIONS CAREFULLY

 and get a thorough understanding of what is required to assemble

to your Type of Pool and Filter System.

2. Before you begin to assemble the UV Sanitizer, identify, count, and check all parts needed for assembly.  Refer to

the “PARTS LIST”, Page #8.

3. It is recommended that you have some PETROLEUM JELLY on hand for lubricating the gaskets.

1. Installer shall follow written instructions provided for operation of the circulation systems.

2. All electrical components shall be installed in accordance with Article 680 of the National Electrical Code (NEC)

“Swimming Pools, Fountains and Similar Installations” or its latest approved edition.

3. The UV Sanitizer is manufactured by Polygroup and designed to be operated at 115 VAC 60 Hz.  (ALL Units must

have a minimum of 105 VAC to start and run properly.)

PRELIMINARY STEPS

IMPORTANT NOTES:

UV Sanitizing System

20.0 Watts

0.4 amps

120VAC

FIG.3 

21

22

23

12

20

19

17

16

15

14

13

14

10

14

27

8

7

9

6

5

4

3

2

1

11

28

4 Ea. 26

4 Ea.

1

2

3

26

2 Ea.

2 Ea.

2 Ea.

2 Ea.

18

Содержание UVS-1012

Страница 1: ...ts of God outside the control of Polygroup IN NO EVENT SHALL POLYGROUP THEIR AUTHORIZED AGENTS RELATED ENTITIES OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES Some states or countries or others jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Should you...

Страница 2: ... Ea 3 1 READ ALL INSTRUCTIONS CAREFULLY and get a thorough understanding of what is required to assemble to your Type of Pool and Filter System 2 Before you begin to assemble the UV Sanitizer identify count and check all parts needed for assembly Refer to the PARTS LIST Page 8 3 It is recommended that you have some PETROLEUM JELLY on hand for lubricating the gaskets 1 Installer shall follow writte...

Страница 3: ...e is protected by a GFCI Receptacle must be at least 10 feet away from pool Do not use an extension cord to connect unit to electric supply provide a properly located outlet Do not bury the cord NOTE The UV Sanitizer consists of UV Sanitizer Power Adapter Hardware Bag Hose Adapters Hose Clamps and Water Hoses The UV Sanitizer can be used with Skimmer Pump Fig 1 or RP Pump Fig 2 filter system A Rem...

Страница 4: ...emove the UV Tube Socket from the defective UV Tube Remove the defective UV Tube 7 Insert a new UV Tube Plug in the UV Tube Socket to the UV Tube Put back the UV Tube End Cover Tighten the UV Tube End Cover with screws Put back the Bottom Cover Tighten the Bottom Cover with screws Done 1 WARNING To reduce the risk of electric shock the parts should be completely dry before servicing Disconnect fro...

Отзывы: