6
6
B. Check the return fitting on the inside of the pool for correct flow, it should feel like a solid stream of water
returning to the pool. You can use the return flow as a gauge to determine when the filter needs cleaning and/or
replacement. If you feel a reduction in flow, clean and/or replace filter.
C. Test water and adjust as needed, see “POOL WATER CARE”, page #8.
VERY IMPORTANT – PUMP AND
FILTER ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN
ONLY BE DONE BY MAINTAINING PROPER CHLORINE AND pH LEVELS AT ALL TIMES!
D. The filter may need to be cleaned and/or replaced several times at start up until the correct chlorine and pH levels
are attained. We recommend that you keep at least one spare cartridge on hand at all times. Filter cartridges may
be purchased at the store you purchased your pool from, or ordered from GFP, see page #10, Item #9.
3. USING AND INSTALLING THE SERVICE PLUGS:
A. You will need to install the two Service Plugs (30) FIG. 1 page # 3 in order to clean the Filter Cartridge (9),
service the Pump (1-6), and to work on the Return Hose (13). When Pump (1-6) needs servicing or working on
the Return Hose (13), or cleaning the Filter Cartridge (9); first, unplug (turn off ) the power and then install the
Service Plug (30) into Pool Wall Fitting (15) after removing Locking Ring (21) and Diverter Fitting (20). Also
install a Service Plug (30) into center hole at the bottom of the Skimmer Canister (8) after removing the Pump
Retaining Nut (7) and insert it as you remove the Pump. See FIG. 1 page #3 for location of each. When service is
complete remove both Service Plugs (30) by reversing the procedures above.
4. FILTER CARTRIDGE CLEANING INSTRUCTIONS:
A. You will need to clean the Filter Cartridge. First, unplug (turn off) the Power Filter. Then remove the Lock Top
(11) by turning it counter clockwise. Remove the Strainer Basket (10) and the Filter Cartridge (9).
B. The filter cartridge can be cleansed of coarse dirt and debris by pressure washing inside and out with a garden
hose, making sure to wash between all pleats. Fine particles of dirt are more easily removed from the filter
pleats when the cartridge is dry. Therefore, after hosing the cartridge, allow the filter to dry and CAREFULLY
BRUSH, but do not scrub the pleated surface areas. Cleaning and scrubbing a filter too vigorously will also wear
out the cartridge much faster than if it is simply hosed off correctly.
C. Suntan oils, body oils, and algae can form a coating on the filter pleats which may not be thoroughly removed by
hosing. Such films of oils and/or algae will rapidly clog up the filters’ pores, greatly reducing filtration. There-
fore, it is imperative to remove such materials from the filter element as soon as possible. To remove oils, we
recommend soaking the cartridge in a solution of
1 pound of trisodium phosphate
(or any other strong deter-
gent)
to 5 gallons of water
for up to
12 hours
. Trisodium phosphate is available in many supermarkets, hard-
ware stores, or janitorial supply stores. After the oils have been removed, rinse the filter cartridge to remove any
dirt. If algae is a problem, add
1/2 pint of pool chlorine
or
1 pint of liquid household bleach
to the cleaning
solution,
1 hour
before removing the filter cartridge from the solution. Thoroughly rinse the filter cartridge be-
fore replacing it in the filter case. Check the pool chemistry to determine the cause of algae growth.
D. Excessive calcium and/or mineral deposits may build up on a filter cartridge and should be handled differently.
Contact your local pool supply store to ask about additional filter cartridge cleaners or treatment for calcium or
mineral deposits. Check pool chemistry for high pH or alkalinity; this may cause a calcium or mineral build-up.
Now is a good time to put chlorine tablets into the Filter (9) if necessary.
E. A spare “stand-by” Filter Cartridge is an excellent investment. It provides a convenient way to continue filtra-
tion of your pool while cleaning or replacing a dirty Filter Cartridge. Also, a well-maintained, clean cartridge
assures you that your filter will always be ready to operate at peak efficiency.
Should you encounter any problems, contact the Customer Service Representative/Parts Department at (800) 813-0206
from 8 AM to 5 PM Mon. thru Fri. EST. Extended operating days and hours during peak season requirements.
