background image

13. FIRMWARE UPDATES

Step 1:

 Download the “setup.exe” executable file from our website 

(http://www.gsmcommander.com)

Step 2:

 Run the executable file 

(See 5.6)

Step 3:
 

Connect Micro Commander to PC via the supplied USB cable

Step 4: 
 

Connect power to the Micro Commander

Step 5:

 Run the Utility (Start > All Programs > GSM Commander V7 0101 > Update Firmware)

The   SmartSetup   software   will   also   automatically   detect   upon   startup   if   the   firmware   currently 
loaded on the Micro Commander unit does not match it's current version. It will then prompt you to 

run the update firmware utility.

Screen 1:

The loader utility will show this screen when 
started.  

Screen 2:

The   loader  utility  will  now   show   this   screen, 

which   means   the   firmware   is   being   updated. 

The green LED, labeled  

“STATUS”

  on the 

Micro Commander, will start flashing.

On completion the loader utility will close and the unit will start up automatically or if you so wish 
you can disconnect the power. 

© Polygon Technologies.   All rights reserved                                                                                          

Page 30

Содержание Micro Commander GC0101





































Отзывы: