manualshive.com logo in svg

Poly Pong CRUISE SHIP ALL-WEATHER, Инструкция по сборке

Поделиться
Скачать
Poly Pong CRUISE SHIP ALL-WEATHER Скачать руководство пользователя страница 13

This step is the hard part.  Use at least four helpers.  You must lift up the table
and carefully turn it right-side-up without putting pressure on the legs against the
floor.  You want to flip it over in the air and then allow the feet to touch the floor.
Once this is done, you can then carry it into the desired location and position.
Fig. 25.

ATTACHING THE BUMPERS

Notice the two threaded inserts on
the bottom side of the bumper.
Fig, 26. Insert a 60 mm screw into
each thread insert and bend the nut
placement if necessary to make
them perpendicular then remove
the screw. These are made to align
up with the two holes, one in the
table  joiner and the other in the
center post top.  Fig. 27.

Take the bumper and place it into
the slot for the bottom protrusion
with the pointed end towards the
table center.  It should settle into
the gap between the two table
tops. Fig. 28 & 29.

Page 12

Fig. 25

Fig. 26

Fig. 27

Содержание CRUISE SHIP ALL-WEATHER

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды