P
P
P
P
A
A
A
A
R
R
R
R
Q
Q
Q
Q
U
U
U
U
E
E
E
E
T
T
T
T
A
A
A
A
C
C
C
C
C
C
C
C
E
E
E
E
S
S
S
S
S
S
S
S
O
O
O
O
R
R
R
R
Y
Y
Y
Y
((
((
G
G
G
G
))
))
This accessory is for use solely with the
Joker brush.
Put the joker brush into place on the parquet
accessory as illustrated in figure 12. Apply
the brush to the accessory as indicated by
the arrow so that the two pieces fit onto each
other and then hook them together. To un-
hook the parquet accessory from the joker
brush pull the two levers on the sides of the
fitting outwards and then lift the brush off
(Fig. 13).
U
U
U
U
S
S
S
S
II
II
N
N
N
N
G
G
G
G
T
T
T
T
H
H
H
H
E
E
E
E
II
II
R
R
R
R
O
O
O
O
N
N
N
N
((
((
O
O
O
O
P
P
P
P
T
T
T
T
II
II
O
O
O
O
N
N
N
N
A
A
A
A
L
L
L
L
))
))
• Connect the iron to the monobloc plug
(
B2
) proceeding as shown in the “Opera-
tion” paragraph.
Check the manufacturer’s label on the gar-
ment, and interpret the symbol on the label
as follows:
• For
STEAM
ironing, set the iron tempera-
ture to its maximum travel on the “COT-
TON - LINEN” steam position by turning
the knob (
Y
).
NB Set at its maximum, do NOT set
against the picture of iron on the knob
(Y)
.
Most fabric types, other than delicates can
be STEAM-ironed at this temperature,
please consult the garment label. If you
want to DRY iron, set the knob (
Y
) to the
required temperature for the fabric as,
shown on the dial.
Nb fabric indications on dial are for
DRY ironing, for STEAM ironing set at
maximum travel as explained above.
• Wait for a few minutes until the Iron heat-
ing” indicator light (
X1
) goes out, to show
that the soleplate of the iron has reached
the required temperature.
• Press the steam request button (
X
) on the
iron to release bursts of steam from the
holes on the soleplate. Release the button
and the steam will stop. When you first
start to use the iron, a few drops of water
may come out of the sole-plate mixed with
the steam due to imperfect heat stabilisa-
tion. It is therefore advisable to direct the
first jet of steam onto a rag.
• In order to obtain a continuous jet of steam
move the sliding switch (
W1
). The steam
will continue to come out even when the
steam request button (
X
) is released. To
stop the flow of steam push the sliding
switch backwards (
W1
).
RECOMMENDED TECHNIQUE
for STEAM
ironing with Polti iron is APPLY steam (but-
ton
X
) on the upstroke, then release button
(
X
) (so no steam) for the backstroke, so re-
closing the fibres, preventing oversteaming
and wetness.
DRY IRONING
• FOR DRY IRONING ONLY (NOT steam
ironing), press the main switch (
1
) and ad-
just the temperature of the iron by turning
dial (
Y
) to the temperature required for the
fabric (as shown on the dial).
NOTE:
using the iron, it is advisable to ad-
just the steam jet at a medium range, or to
do some testing in order to find the jet which
is more suitable to the fabric to be ironed.
IMPORTANT NOTE
• Do not leave the iron unattended whilst
connected to the mains.
Steam ironing allowed--set the dial to its
MAXIMUM travel at the end of the 3
dots symbol on your Polti iron
Steam ironing allowed--set the dial to its
MAXIMUM travel at the end of the
THREE (nb THREE, not two) dots sym-
bol on your Polti iron
DRY IRON only, with iron dial set at one
dot. N.B. NEVER CALL FOR STEAM
BY PRESSING STEAM REQUEST
BUTTON when DRY ironing. See spe-
cial instructions for DRY ironing in the
instruction book.
DO NOT IRON. Neither steam nor dry
ironing allowed.
LECOASPIRA AS720 LUX
61
VT AS720KUX - M0S07341 1M07.qxp 04/07/2006 16.42 Pagina 61
