the arrow so that the two pieces fit onto each
other and then hook them together. To un-
hook the parquet accessory from the joker
brush pull the two levers on the sides of the
fitting outwards and then lift the brush off
(Fig. 13).
U
U
U
U
S
S
S
S
II
II
N
N
N
N
G
G
G
G
T
T
T
T
H
H
H
H
E
E
E
E
II
II
R
R
R
R
O
O
O
O
N
N
N
N
((
((
7
7
7
7
1
1
1
1
0
0
0
0
K
K
K
K
ii
ii
tt
tt
))
))
• Connect the iron to the monobloc plug
(
B2
) proceeding as shown in the “Opera-
tion” paragraph.
Check the manufacturer’s label on the gar-
ment, and interpret the symbol on the label
as follows:
• For
STEAM
ironing, set the iron tempera-
ture to its maximum travel on the “COT-
TON - LINEN” steam position by turning
the knob (
Y
).
NB Set at its maximum, do NOT set
against the picture of iron on the knob
(Y)
.
Most fabric types, other than delicates can
be STEAM-ironed at this temperature,
please consult the garment label. If you
want to DRY iron, set the knob (
Y
) to the
required temperature for the fabric as,
shown on the dial.
Nb fabric indications on dial are for
DRY ironing, for STEAM ironing set at
maximum travel as explained above.
• Wait for a few minutes until the Iron heat-
ing” indicator light (
X1
) goes out, to show
that the soleplate of the iron has reached
the required temperature.
• Press the steam request button (
X
) on the
iron to release bursts of steam from the
holes on the soleplate. Release the button
and the steam will stop. When you first
start to use the iron, a few drops of water
may come out of the sole-plate mixed with
the steam due to imperfect heat stabilisa-
tion. It is therefore advisable to direct the
first jet of steam onto a rag.
• In order to obtain a continuous jet of steam
move the sliding switch (
W1
). The steam
will continue to come out even when the
steam request button (
X
) is released. To
stop the flow of steam push the sliding
switch backwards (
W1
).
RECOMMENDED TECHNIQUE
for STEAM
ironing with Polti iron is APPLY steam (but-
ton
X
) on the upstroke, then release button
(
X
) (so no steam) for the backstroke, so re-
closing the fibres, preventing oversteaming
and wetness.
DRY IRONING
• FOR DRY IRONING ONLY (NOT steam
ironing), press the main switch (
1
) and ad-
just the temperature of the iron by turning
dial (
Y
) to the temperature required for the
fabric (as shown on the dial).
NOTE:
using the iron, it is advisable to ad-
just the steam jet at a medium range, or to
do some testing in order to find the jet which
is more suitable to the fabric to be ironed.
IMPORTANT NOTE
• Do not leave the iron unattended whilst
connected to the mains.
• Iron only on heat resistant surfaces and on
surfaces that allow the steam to escape
e.g. mesh ironing boards.
• In case of accidental fall of the appliance it
is necessary to have it checked by an au-
thorized service center as the internal
Steam ironing allowed--set the dial to its
MAXIMUM travel at the end of the 3
dots symbol on your Polti iron
Steam ironing allowed--set the dial to its
MAXIMUM travel at the end of the
THREE (nb THREE, not two) dots sym-
bol on your Polti iron
DRY IRON only, with iron dial set at one
dot. N.B. NEVER CALL FOR STEAM
BY PRESSING STEAM REQUEST
BUTTON when DRY ironing. See spe-
cial instructions for DRY ironing in the
instruction book.
DO NOT IRON. Neither steam nor dry
ironing allowed.
LECOASPIRA 710 - 710 KIT
61
Lecoaspira 710-710kit - M0S07340 1M05.qxp 22/06/2006 12.23 Pagina 61
Содержание Vaporetto Lecoaspira 710 Kit
Страница 1: ......
