background image

IK-E286-001E 

The EKS-4001 monitoring and controlling element covered by the present manual complies with the 
requirements of the following European Union Directives: 
 

CPD

  

89/106/EWG  on construction materials; 

EMC

   2004/108/WE   on electromagnetic compatibility. 

 
The EKS-4001 element has been approved with the EC-Certificate of Conformity No. 1438/CPD/0071 
issued  by  the  Scientific  and  Research  Centre  for  Fire  Protection 

(CNBOP)  Józefów,  Poland,  a

n  EU 

notified  authority  No.  1438,  confirming  its  compliance  with  the  requirements  of  PN-EN  
54-18:2006 (U) standard. 
 
The certificate may be downloaded from 

www.polon-alfa.pl

 web site.

 

 
 

 

 

1438 

Polon-Alfa 

Spółka z ograniczoną odpowiedzialnością Sp. k.

 

155, Glinki Street, PL 85-861 Bydgoszcz, POLAND 

06 

1438/CPD/0071 

EN 54-18 

Input/output device

  

EKS-4001 addressable monitoring and controlling element 

Technical data - IK-E286-001 manual 

 
 
Read the manual carefully before the detector assembling and commissioning. 

Any  nonconformity  with  the  instructions  contained  in  the  manual  may  be  harmful  or  may  cause 
violation of the law in force  

POLON-ALFA  bears  no  responsibility  for  any  damage  resulting  from  usage  inconsistent  with  the 
manual. 

 

A  waste  product,  unsuitable  for  further  use,  shall  be  passed  to  
a waste electric and electronic equipment collection point. 

 

 

 

NOTE:  The manufacturer reserves the right to change specifications of products at any time 

without prior notice. 

Содержание EKS-4001












Отзывы: