Polaroid SprintScan SS35 Скачать руководство пользователя страница 91

Страница: 91 / 187

Slide Scanner Repair Manual

Parts Replacement

Transporter Stepper Motor

1. Remove the top housing.

2. Remove the main controller PC board.

3. If applicable, remove the two (2) screws that secures the light tunnel to the chassis mount

and then lift off the light tunnel.

4. Remove the chassis assembly.

5. Remove the two (2) screws securing the nut guide to the chassis mount (Figure 4-14) and then

lift off the nut guide.

WARNING

DO NOT REMOVE THE TWO STOPS ON THE BALL SLIDE.

5. Remove the three (3) screws securing the transporter stepper motor to the chassis .

6. Gently pull down the transporter stepper motor and then lift it out. Replace it with a new one.

7. Install a new nut onto the replacement transporter stepper motor lead screw.

Note: Always replace the lead screw nut when replacing the stepper motor.

8. Re-install the transporter stepper motor.

9. Re-install the nut guide.

10. Re-install the chassis assembly.

11. If applicable, re-install the light tunnel.

12. Re-install the main controller PC board.

13. Re-install the top housing.

14. Run LabVIEW Motion test to make sure slide scanner is OK.

Содержание SprintScan SS35




























































































































































































Результаты поиска

Содержание SprintScan SS35

Отзывы:

Похожие инструкции для SprintScan SS35

Бренды по названию

Популярные бренды

Polaroid SprintScan SS35, Руководство по ремонту

Результаты поиска

Содержание SprintScan SS35

Отзывы:

Похожие инструкции для SprintScan SS35

Бренды по названию

Популярные бренды