Polaroid Land SX-70 Скачать руководство пользователя страница 54

Страница: 54 / 54

Figure 4-9 Shutter mount retaining screws

5. In the following step, the bottom cover will be

removed. To prevent damage to the flex circuit,

insert a thin strip (a small, metal, six-inch pocket

scale, for example) between flex circuit and the

inside cover surface. Move the tool from one

locating stud to the other as the cover is being

removed to prevent sticking to the flex circuit.
6. Lift the cover a small distance away from the

camera, then slide the cover from the assembly.
7. remove the inner-frame-to-boot-retainer

screws (Figure 4-8).

8. Remove the four shutter housing retaining

screws from the rear of the shutter mounting

hinge bracket (Figure 4-9). (Check for square

head or Bristol head screw. Replace with same

type.)

Caution : While the shutter is detached from the

mounting bracket, make sure no mechanical

stress is put on the ribbon cable.
9. Remove the two hinge-bracket-to-boot-

retainer screws located adjacent to the round

lens opening in the shutter hinge bracket. (Newer

cameras have rivets which must be removed.)

Figure 4-8 Boot retaining screws

Содержание Land SX-70























































Результаты поиска

Содержание Land SX-70

Отзывы:

Похожие инструкции для Land SX-70

Бренды по названию

Популярные бренды

Polaroid Land SX-70, Руководство пользователя

Результаты поиска

Содержание Land SX-70

Отзывы:

Похожие инструкции для Land SX-70

Бренды по названию

Популярные бренды