Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 96 / 147

background image

6. Elevate the vehicle until the wheel is slightly off the ground.

7. Remove the wheel nuts and remove the wheel.

WHEEL INSTALLATION

1. With the transmission in gear and the park brake set, place the wheel on the

wheel hub. Be sure the valve stem is toward the outside and rotation arrows
on the tire point toward forward rotation.

2. Install the wheel nuts and finger-tighten them.

NOTE

On vehicles with tapered rear wheel nuts, make sure the tapered end of the nut

goes into the taper on the wheel.

3. Tighten all wheel nuts in a star pattern to specification.

TORQUE

75 ft-lbs (102 Nm)

4. Lower the vehicle and remove the floor jack.

SPARK PLUGS

SPARK PLUG RECOMMENDATIONS

Refer to the specifications section beginning on page 121 for the recommended
spark plug type and gap for your vehicle. Torque spark plugs to specification
after installing.

NOTICE

Using non-recommended spark plugs can result in serious engine damage.

Always use the recommended spark plugs.

SPARK PLUG SPECIFICATIONS

Spark Plug Type

AC Delco 41-103 or equivalent

Spark Plug Torque

15 ft-lbs (20 Nm)

Inspect and replace spark plugs at the intervals recommended in the Periodic
Maintenance Chart beginning on page 67. Inspect spark plugs when the engine
is warm. Always replace spark plugs in sets of four.

94

Downloaded from

«
...
94
95
96
97
98
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Harken Hoister Страницы: 12

Бренд: Yamaha Страницы: 2

Бренд: JANE Страницы: 21

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: Allen Sports Страницы: 2

Бренд: minnid Страницы: 44

Бренд: METRON Страницы: 4

Бренд: Whispbar Страницы: 15

Бренд: Fiat Страницы: 284

Бренд: Hyundai Страницы: 168

Бренд: CSL Страницы: 8

Бренд: Kuda Страницы: 3

Бренд: Mitsubishi Страницы: 57

Бренд: Metra Electronics Страницы: 10

Бренд: Alu-Cab Страницы: 6

403.NISS4HT 2.36 RSR

Бренд: Directed Страницы: 22

Бренд: Jotto Desk Страницы: 3

Proguard 100021

Бренд: walser Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды