manualshive.com logo in svg

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Поделиться
Скачать
Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 86

DRIVE BELT WEAR ANALYSIS

Internal tooth cracks 
(hairline): OK to run, 

but monitor 

condition

External tooth 

cracks: Replace belt

Missing teeth: 

Replace belt

Chipping (not 

serious): OK to run, 

but monitor 

condition

Fuzzy edge cord: 

OK to run, but 

monitor condition

Hook wear: Replace 

belt

Stone damage: 

Replace belt if 

damage is on edge

Bevel wear 

(outboard edge 

only): OK to run, but 

monitor condition

DRIVE BELT CLEANING

Cleaning the drive belt will maximize belt and sprocket life and minimize drive 
line noise. Clean the belt at every tire change. Clean the belt more often if 
operating in dirty, dusty or high debris environments.

1.  Mix a few drops of mild dish soap with a cup of warm water.

2.  Use a soft nylon brush to clean the belt and sprocket teeth with the soapy 

water. Clean well in corner areas where road debris and belt dust can collect.

3.  Rinse the belt with clear water, then dry thoroughly.

NOTE

Do not inspect or adjust drive belt tension when the belt is wet. Improper 

adjustment will result.

SUSPENSION INSPECTIONS

Always inspect the suspensions at the intervals outlined in the Periodic 
Maintenance Chart beginning on page 67. Refer to the 

SLINGSHOT Service 

Manual

, or your authorized dealer can assist.

FUEL SYSTEM COMPONENTS

Inspect fuel lines and connections for wear, deterioration, kinks, damage or 
leaks. Promptly see your dealer for service if any of these conditions exist.

84

MAINTENANCE

Downloaded from 

ManualsNet.com

 search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды