Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 79 / 147

3. Reinstall the fill plug.

TORQUE

10-14 ft-lbs (14-19 Nm)

4. See your dealer for service. A low fluid level indicates a fluid leak.

FLUID CHANGE

1. Elevate the vehicle using appropriate jack stands. Make sure the elevated

vehicle is level.

2. Remove the fill plug

3. Place a drain pan under the drain plug

4. Remove the drain plug. Allow the fluid to drain completely.

5. Clean and reinstall the drain plug. Torque to specification.

TORQUE

10-14 ft-lbs (14-19 Nm)

NOTE

Use a syringe to add the fluid. If a syringe is not available, remove the battery

and use a funnel and tube to add the fluid.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды