Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 17 / 147

background image

FUEL AND EXHAUST SAFETY

Always heed these fuel safety warnings when refueling or servicing the fuel
system. For fuel recommendations and fueling procedures, see page 54.

WARNING

Gasoline is highly flammable and explosive under certain conditions.

•  Always exercise extreme caution whenever handling gasoline.
•  Always turn off the engine before refueling.
•  Always refuel outdoors or in a well-ventilated area.
•  Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.
•  Do not smoke or allow open flames or sparks in or near the area where

refueling is performed or where gasoline is stored.

WARNING

Gasoline and gasoline vapors are poisonous and can cause severe

injury.

• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you

swallow gasoline, inhale more than a few breaths of gasoline vapor, or get
gasoline in your eyes, see a physician immediately.

• If gasoline spills on your skin or clothing, immediately wash it off with soap

and water and change clothing.

WARNING

Exhaust gases contain carbon monoxide, a colorless, odorless gas that

can cause loss of consciousness or death in a short time.

• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.

CAUTION

Use of after-market exhaust components is not recommended.

15

Downloaded from

«
...
15
16
17
18
19
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

iBoard IB-ZK406

Бренд: APS Auto Parts Specialist Страницы: 3

FleetMaster Air FW8 Series

Бренд: SAF-HOLLAND Страницы: 20

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Subaru Страницы: 34

Бренд: Compass Страницы: 16

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

2012 Truck Chassis cab

Бренд: RAM Страницы: 506

Бренд: Toro Страницы: 24

Бренд: iArmor Страницы: 6

Бренд: Belkin Страницы: 2

Бренд: Vangear Страницы: 5

Бренд: Safe Fleet Страницы: 20

Бренд: Mitsubishi MOTORS Страницы: 416

MagicSpeed MS900

Бренд: Waeco Страницы: 120

Бренд: Mazda Страницы: 604

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды