Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 11

Страница: 11 / 147

SAFETY

SAFETY GUIDELINES

WARNING

Improper vehicle use can result in SEVERE INJURY or DEATH.

ALWAYS WEAR AN APPROVED FULL-FACE HELMET.

ALWAYS WEAR EYE PROTECTION AND SEAT BELT.

NEVER USE WITH DRUGS OR ALCOHOL.

READ OWNER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND
WARNINGS.

NEVER OPERATE:

• If you are under the age of 16 and without a driver’s license with motorcycle

endorsement.

• Under the influence of drugs or alcohol.
• Unless all occupants are able to sit with back against the seat and feet firmly

on the floorboard.

•  With a child safety seat installed in this vehicle.
•  While using a mobile phone or other handheld device.
•  Off-road.

SAFETY

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды