Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 147

background image

SAFE DRIVING PRACTICES

OPERATING A SLINGSHOT VEHICLE HAS INHERENT
RISKS.

You can minimize those risks, but you can’t eliminate them completely. Even if
you’re an experienced 3-wheel vehicle operator or passenger, read all of the
safety information in this manual before operating this SLINGSHOT vehicle.

• Take a 3-wheel vehicle rider course from the Motorcycle Safety Foundation or

another qualified instructor. The course will help you learn effective turning
and braking techniques, traffic strategies and evasive maneuvers, in addition
to general safe riding habits. To locate a rider course in your area, contact the
Motorcycle Safety Foundation at 1-800-446-9227 or visit their web page at
www.msf-usa.org. You may also contact your dealer or the motorcycle
regulatory agency in your area of operation.

• Observe all maintenance requirements specified in this manual. See the

SLINGSHOT Service Manual

for assistance. Your authorized SLINGSHOT

dealer can also provide assistance.

DESIGN CHARACTERISTICS AFFECT HOW YOU
SHOULD OPERATE THE SLINGSHOT VEHICLE:

• The SLINGSHOT is a lightweight 3-wheel vehicle. As such, it will respond

differently than other on-road vehicles in various road and weather conditions.
Thoroughly read your owner’s manual and take safety training before
operating the SLINGSHOT.

• The SLINGSHOT vehicle is designed for on-road use by one operator with

one passenger. The Manufacturing Information label placed on the vehicle
contains the Vehicle Identification Number (VIN), Gross Vehicle Weight
Rating (GVWR) and Gross Axle Weight Rating (GAWR) information.

Never

exceed the GVWR or the GAWR

.

• Driving off-road, driving at excessive speeds, driving with more than one

passenger or carrying weight exceeding the maximum weight rating can
make handling difficult, which could cause loss of control resulting in injury or
death.

• Since the SLINGSHOT has a single, centered rear wheel, “straddling”

obstacles with the front tires increases the likelihood that you will encounter
the obstacles with the rear tire.

• Read the section in this manual entitled

SLINGSHOT Vehicles vs. Other On-

Road Vehicles

• During the first 500 miles (800 km) of operation, follow all break-in procedures

as outlined in the owner’s manual. Failure to do so can result in serious
engine damage.

12

Downloaded from

«
...
12
13
14
15
16
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

2011 Corolla LE

Бренд: Toyota Страницы: 19

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренд: Safe Fleet Страницы: 38

VIEWLINE 52 MM - MOUNTING 11-09

Бренд: VDO Страницы: 4

Бренд: Jaeger Страницы: 13

Бренд: GYS Страницы: 32

Бренд: Rugged Ridge Страницы: 5

Бренд: QA1 Страницы: 3

XC70 - ANNEXE 808

Бренд: Volvo Страницы: 8

Бренд: Kuda Страницы: 3

Бренд: Axxess Страницы: 4

Advanced Million Color

Бренд: LedGlow Страницы: 4

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Sportsman 40-0125

Бренд: Westin Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды