Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 108 / 147

•

Clockwise

adjustment

lowers

the beam

•

Counter-clockwise

adjustment

raises

the beam

AUXILIARY HEADLAMP AIM ADJUSTMENT (USA)

1. Verify that headlamp aim inspection conditions are met. See page 104.

2. Position the vehicle on a level surface with the nose 5 ft. (1.5 m) from a wall

3. Move the ignition switch to the ON position to turn the lights on.

4. Observe the auxiliary headlight beam display on the wall. The lower edge of

the beam displays with a multi-colored halo.

5. Measure from the floor to the bottom edge of the halo’s green band as

illustrated. When the beam is properly adjusted, this measurement should be
in the following range:

106

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды