Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 105 / 147

background image

5. Batteries will self-discharge more quickly when dirty. Periodic cleaning of the

battery terminals using a terminal brush will help maximize battery life. Wash
terminals with a solution of one tablespoon baking soda and one cup water.
Rinse well with tap water and dry off with clean shop towels. Coat the
terminals with dielectric grease or petroleum jelly.

6. Battery connections should be tightened to the correct torque during

installation. This will reduce voltage drop and ensure a reliable connection
between the alternator and battery.

HEADLAMP BULB REPLACEMENT

When servicing a halogen lamp (bulb), avoid touching the lamp with bare
fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten
the life of the lamp. If fingers do touch a lamp, clean it with denatured alcohol.

OUTER HEADLAMPS

1. Pull the sealing boot away from the back of the bulbs and housing.

2. Press the looped end of the wire bulb retainer clip and swing the end toward

the center of the bulb to release it from the latch tab.

3. With the wire connector attached, pull the bulb out.

4. Disconnect the wire harness. Install the new bulb and secure the retainer.

5. Reinstall the sealing boot. Make sure it seals tightly around the bulb base

and lens to seal off from moisture.

CENTER HEADLAMPS (IF EQUIPPED)

1. Disconnect the headlight wiring harness at the rear of the headlights.

2. From the rear of the headlight, grasp the bulb housing and rotate it counter-

clockwise to remove it.

3. Install the new bulb and rotate it clockwise to secure it.

4. Reconnect the wiring harness.

103

Downloaded from

«
...
103
104
105
106
107
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Kargo Master Страницы: 5

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

Бренд: Harmar Mobility Страницы: 10

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: Scion Страницы: 24

TX-STAMP-4-FC04

Бренд: Over Armour Offroad Страницы: 9

Бренд: S&B Filters Страницы: 4

Бренд: Mazda Страницы: 3

Бренд: Xpresskit Страницы: 12

Performer-Plus 2172

Бренд: Edelbrock Страницы: 4

Бренд: Scosche Страницы: 8

Auto-Dimming Mirror

Бренд: Mazda Страницы: 2

Бренд: Conrad Страницы: 8

Бренд: Genesis Страницы: 690

Truck 2500 2018

Бренд: RAM Страницы: 32

Бренд: Kia Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды