Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 102 / 147

background image

BATTERY STORAGE

Whenever the vehicle is not used for a period of one month or more, remove the
battery from the vehicle, ensure that it’s fully charged, and store it out of the sun
in a cool, dry place. Check battery voltage each month during storage and
recharge as needed to maintain a full charge.

BATTERY CHARGING

AGM BATTERY CHARGER RECOMMENDATIONS

Slingshot vehicles utilize Absorbent Glass Mat (AGM) batteries which are
selected for their superior vibration resistance, weight savings, and high output.
Polaris recommends using the BatteryMINDer® 2012 AGM - 2 AMP battery
charger (PN 2830438) to charge and maintain AGM batteries. The charger can
be found on the Polaris PG&A website and ordered in DEX – Item Availability.

Batteries that fall below 12.5V run the risk of sulfation, a condition whereby
sulfate crystals form inside the battery and significantly reduce performance.
AGM chargers are designed specifically for charging AGM type batteries and
use high frequency pulses to partially reverse sulfation.

IMPORTANT

The use of non-AGM battery chargers or non-AGM battery tenders may result

in a misleading “battery not found” or “open cell” fault message. Please ensure

you are using the recommended AGM charger when charging AGM type

batteries.

AGM BATTERY TESTING PROCEDURE

1. Test battery using the battery tester PU-50296.

2. If the tester indicates a test result other than “Good Battery,” follow the steps

below before replacing the battery:

a. Connect battery to the recommended battery charger. If charging

sequence begins as normal, fully charge battery and proceed to step 3.

The time listed on the PU-50296 battery tester printout is an estimate.
The recommended automatic charger will indicate when the battery is
fully charged on its display.

b. If charging sequence does not initialize, refer to

AGM Battery Charging

Recommendations – Deeply Discharged (below 3 volts)

to attempt to

restore the deeply discharged battery. If charging sequence will not finish
as intended, the battery needs to be replaced.

3. Re-test battery. If the test results show that battery failed, proceed with

battery replacement.

100

Downloaded from

«
...
100
101
102
103
104
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Federal Signal Corporation Страницы: 13

Бренд: Daihatsu Страницы: 340

Бренд: Jeep Страницы: 25

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

Бренд: Uebler Страницы: 56

Бренд: Nuna Страницы: 17

Бренд: Mazda Страницы: 122

Бренд: Ecco Страницы: 12

V70XC Cross country 1998

Бренд: Volvo Страницы: 262

Бренд: Great Wall Страницы: 18

Бренд: WIX Страницы: 2

Бренд: travall Страницы: 2

Бренд: Gacell Страницы: 12

Бренд: Mobility Networks Страницы: 52

Бренд: Unex Страницы: 30

PRIME DESIGN HXR-269-E-UM3-80

Бренд: Safe Fleet Страницы: 12

Бренд: Toyota Страницы: 285

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды