Polaris RZR 570 2013 Скачать руководство пользователя страница 352 | Manualshive

Страница: 352 / 482

background image

8.16

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

SERVICE PREPARATION

NOTE

Do not reuse a ball joint if it has been removed. If

removed, it must be replaced. Use this removal

procedure only when replacing the ball joint.

Ball joint tool PU-50506 will allow the upper and lower

ball joints to be replaced with the A-arm installed on the

vehicle.

The A-arm does not need to be removed to perform this
procedure if ball joint tool PU-50506 is used.

1.

Properly lift and support the vehicle by the frame.

2.

Remove the appropriate front wheel.

3.

To service the upper ball joint:

- Remove and discard the two front brake caliper
mounting bolts and remove the caliper from the
brake disc (see Chapter 9 – Caliper Removal , page
9.21).
- Remove and discard the upper ball joint pinch bolt.
- If necessary, remove the lower front shock fastener
from the A-arm to gain enough clearance to install
ball joint tool (PU-50506) on the upper ball joint.

4.

To service the lower ball joint:

- Remove and discard the lower ball joint pinch bolt.
- If necessary, remove the lower front shock fastener
from the A-arm to gain enough clearance to install
ball joint tool (PU-50506) on the lower ball joint.

BALL JOINT REMOVAL

1.

Remove the retaining ring from the ball joint.

2.

Install Spacer (A) over the top of the ball joint face.

3.

Place Removal Adaptor (B) over the ball joint shaft.

4.

Install the Press Asm. (C) onto the A-arm to engage
the ball joint Removal Adapter.

NOTE

Be sure the Press Asm. opening is only contacting the

Spacer (A) and not the ball joint face.

STEERING / SUSPENSION

«
...
350
351
352
353
354
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Yerf-Dog Страницы: 21

Бренд: Baltmotors Страницы: 58

Бренд: E-TON Страницы: 134

Бренд: VANDERHALL Страницы: 109

Бренд: Suzuki Страницы: 54

Бренд: Ardisam Страницы: 10

Off-Roader 36EL

Бренд: Texas Страницы: 27

Бренд: Austin Motor Company Страницы: 124

Бренд: Taylor-Dunn Страницы: 232

Бренд: Daymak Страницы: 28

Bomag MPH 122-2

Бренд: Fayat Group Страницы: 198

Бренд: Taylor-Dunn Страницы: 240

Бренд: Equinox Systems Страницы: 6

2015 WILDCAT SPORT

Бренд: Arctic Cat Страницы: 68

Бренд: Arctic Cat Страницы: 84

Бренд: Arctic Cat Страницы: 177

Бренд: Arctic Cat Страницы: 190

DVX 90/90 UTILITY

Бренд: Arctic Cat Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды