manualshive.com logo in svg

Polaris RANGER CREW 900 2014, Руководство пользователя

Поларис РЕЙНДЖЕР КРУ 900 2014 - это надежный и мощный многофункциональный транспортный средство для командной работы. Вы сможете найти руководства по эксплуатации на нашем сайте, где их можно бесплатно скачать. Посетите manualshive.com для загрузки.

Поделиться
Скачать
background image

10

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.33

BATTERY SERVICE

BATTERY SPECIFICATIONS

Battery PN 4014043 / 4014132-P

Type

Polaris Maintenance Free

Voltage

12 Vdc

Nominal Capacity
@ 20 HR Rate

32 AH

CCA - 2013 Models

Deka - 450
Johnson Controls - 575

CCA - 2014 Models

Johnson Controls - 575

Nominal Open
Circuit Voltage

12.8 Vdc or more.

Recommended
Charging Rate

1.8A @ 5-10 HR or 6.0A @ 1
HR

NOTE

Never attempt to open the battery.

GENERAL BATTERY INFORMATION

WARNING

CALIFORNIA PROPOSITION 65 WARNING:Batteries,

battery posts, terminals and related accessories contain

lead and lead compounds, and other chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm. WASH HANDS

AFTER HANDLING.

WARNING

Battery electrolyte is poisonous. It contains acid!

Serious burns can result from contact with the skin,

eyes, or clothing.ANTIDOTE:External: Flush with water.

Internal: Drink large quantities of water or milk. Follow

with milk of magnesia, beaten egg, or vegetable oil. Call

a physician immediately.Eyes: Flush with water for 15

minutes and get prompt medical attention.Batteries

produce explosive gases. Keep sparks, flame,

cigarettes, etc. away. Ventilate when charging or using

in closed space. Always shield eyes when working near

batteries.Keep out of reach of children.

1.

Check battery voltage with a volt/ohm meter. A fully
charged battery should be 12.8 V or higher.

2.

If the voltage is below 12.6 V, the battery will need to
be recharged (see “Charging Procedure”).

To service a Maintenance Free battery:

3.

Remove battery from the vehicle (see Chapter 2).

4.

Test battery with a voltage meter or load tester to
determine battery condition. This will determine the
length of time required to charge the battery to full
capacity. Refer to OCV table (see “OCV - Open
Circuit Voltage Test”).

5.

Charge the battery as recommended (see “Charging
Procedure”).

BATTERY TERMINAL BLOCK

The terminal block (A) is located under the hood near the
radiator pressure cap. The terminal block provides easy
hookup for accessories.

TORQUE

Terminal Block Nuts:

20-25 in-lbs (2.3-2.8 Nm)

ELECTRICAL

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Dazon Raider Extreme 1100D Owner'S Manual preview
Raider Extreme 1100D
Бренд: Dazon Страницы: 85
Taylor-Dunn R0-380-36 Service And Replacement Parts Manual preview
R0-380-36
Бренд: Taylor-Dunn Страницы: 144
Polaris 600 SWITCHBACK Owner'S Manual preview
600 SWITCHBACK
Бренд: Polaris Страницы: 142
Can-Am 2010 DPS Technical Manual preview
2010 DPS
Бренд: Can-Am Страницы: 58
Hammerhead SUPER 250 2008 Owner'S Manual And Parts Manual preview
SUPER 250 2008
Бренд: Hammerhead Страницы: 70
Argo 8x8 Titan Operator'S Manual preview
8x8 Titan
Бренд: Argo Страницы: 64
Can-Am MAVERICK X3 Series 2017 Operator'S Manual preview
MAVERICK X3 Series 2017
Бренд: Can-Am Страницы: 155
Dongfang Motor DF150GK Series Assembly Instruction Manual preview
DF150GK Series
Бренд: Dongfang Motor Страницы: 19
Ultra-tow 49804 Owner'S Manual preview
49804
Бренд: Ultra-tow Страницы: 9
Xxxlutz Jimmy Lee Manual preview
Jimmy Lee
Бренд: Xxxlutz Страницы: 58
E-TON Vector 250R Owner'S Manual preview
Vector 250R
Бренд: E-TON Страницы: 35
Honda 1985 ATC200S Owner'S Manual preview
1985 ATC200S
Бренд: Honda Страницы: 68
Honda 1985 Four Trax 250 Owner'S Manual preview
1985 Four Trax 250
Бренд: Honda Страницы: 74
GAS GAS WILD HP 50 User Manual preview
WILD HP 50
Бренд: GAS GAS Страницы: 60
U-Line H-4121 Quick Start Manual preview
H-4121
Бренд: U-Line Страницы: 8
Yamaha Big Bear YFM350UBL Owner'S Manual preview
Big Bear YFM350UBL
Бренд: Yamaha Страницы: 170
Westward GO-4 INTERCEPTOR.IV Operator'S Manual preview
GO-4 INTERCEPTOR.IV
Бренд: Westward Страницы: 40
Peg-Perego CORRAL T-REX 2011 Use And Care Manual preview
CORRAL T-REX 2011
Бренд: Peg-Perego Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды